HP Indigo 10000 B&R Drivers Troubleshooting -- Document P/N:CA493-00610 Re - Page 37

If the LED is still not lit green, check if there were any phase detection notifications at

Get HP Indigo 10000 PDF manuals and user guides View all HP Indigo 10000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

b. Auxiliary power supply (24 V) RDY LED is lit green. If the LED is OFF and the 560 V power supply is active, replace the auxiliary power supply module. 10. If the L/D1 LED is not blinking, do the following: ● Check POWERLINK (Ethernet) connections. ● Check that the POWERLINK (Ethernet) hub is operational. 11. If the R/E indication LED is not lit green, do the following: a. If the LED is OFF, check the 72 V power supply. b. If the LED is still OFF, the network interface failed. 12. If the 72 V power supply failed, check that: a. RDY LED is lit green in all 72 V power supplies. i. If the LED is not lit green, check input power supply connector X1. ii. If the LED is still not lit green, check if there were any phase detection notifications at the UI. b. X2Xr LED is lit green in all 72 V power supplies. i. If the LED is not lit green, check the preceding (according to the press wiring diagram) module's X2X output connection at connector X5 (pins 7,8,9). ii. If the LED is still not lit green, check the X2X input connection, connector X5 (pins 3,4,5). iii. If the LED is still not lit green, check the preceding (according to the press wiring diagram) module's X2X connection: X20BT9100 for its output X2X connection (pins 1/1, 2/1, 2/2) and that the X LED is ON. Instructions 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
b.
Auxiliary power supply (24 V) RDY LED is lit green. If the LED is OFF and the 560 V power supply
is active, replace the auxiliary power supply module.
10.
If the L/D1 LED is not blinking, do the following:
●
Check POWERLINK (Ethernet) connections.
●
Check that the POWERLINK (Ethernet) hub is operational.
11.
If the R/E indication LED is not lit green, do the following:
a.
If the LED is OFF, check the 72 V power supply.
b.
If the LED is still OFF, the network interface failed.
12.
If the 72 V power supply failed, check that:
a.
RDY LED is lit green in all 72 V power supplies.
i.
If the LED is not lit green, check input power supply connector X1.
ii.
If the LED is still not lit green, check if there were any phase detection notifications at the
UI.
b.
X2Xr LED is lit green in all 72 V power supplies.
i.
If the LED is not lit green, check the preceding (according to the press wiring diagram)
module's X2X output connection at connector X5 (pins 7,8,9).
ii.
If the LED is still not lit green, check the X2X input connection, connector X5 (pins 3,4,5).
iii.
If the LED is still not lit green, check the preceding (according to the press wiring diagram)
module's X2X connection: X20BT9100 for its output X2X connection (pins 1/1, 2/1, 2/2) and
that the X LED is ON.
Instructions
35