HP LH4r HP Netserver LT 6000r Installation Guide - Page 117

is accepted, and the Re-Enter New Password or Enter New Password

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

Chapter 10 Configuring the HP NetServer 3. If necessary, use the arrow keys to move to the Power-On Password menu selection, and press Enter. The Power-On Password is highlighted by default when the Security menu is selected. The first line in the menu, "Administrator Password is [Set or Not Set]": ◊ If no password has been set, then "Not Set" appears in the field. If this is the case, you are not allowed to make any selections in this menu until you set an administrator password. The administrator password controls access to the Setup Utility and its settings. The User Password ahs only limited access to the Setup Utility, such as date, time, and password. ◊ If "Set" is in the field, you can change the password or make other selections in the menu. However, you must start with the user password, but can choose to skip setting the user password. NOTE You must set the administrator password before changing a user password or configuring the HP NetServer to boot with a password. 4. Press Enter to enter a new password or change the old one. A pop-up menu appears: "Set Power-On Password." If no password has been entered, the "Enter New Password" field is highlighted. If a previous password has been entered, the "Enter Old Password" field is highlighted. 5. Enter the password in the appropriate field, and press Enter. The password is accepted, and the "Re-Enter New Password" or "Enter New Password" field is highlighted. For security reasons, the password does not appear on the screen. 6. If necessary, enter the new password in the "Enter New Password" field. 7. Enter the new password in the "Re-Enter New Password" field. After re-entering the new password, a pop-up menu is displayed, asking you to confirm your selection. NOTE To leave the pop-up menu without entering a password, press the Esc key. 109

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Chapter 10
Configuring the HP NetServer
109
3.
If necessary, use the arrow keys to move to the Power-On Password menu
selection, and press
Enter
.
The Power-On Password is highlighted by default when the Security menu
is selected.
The first line in the menu, "Administrator Password is [Set or Not Set]":
◊
If no password has been set, then "Not Set" appears in the field. If this
is the case, you are not allowed to make any selections in this menu
until you set an administrator password.
The administrator password controls access to the Setup Utility and its
settings. The User Password ahs only limited access to the Setup
Utility, such as date, time, and password.
◊
If "Set" is in the field, you can change the password or make other
selections in the menu. However, you must start with the user
password, but can choose to skip setting the user password.
NOTE
You must set the administrator password before changing a
user password or configuring the HP NetServer to boot with a
password.
4. Press
Enter
to enter a new password or change the old one. A pop-up
menu appears: "Set Power-On Password." If no password has been entered,
the "Enter New Password" field is highlighted.
If a previous password has been entered, the "Enter Old Password" field is
highlighted.
5.
Enter the password in the appropriate field, and press
Enter
. The password
is accepted, and the "Re-Enter New Password" or "Enter New Password"
field is highlighted. For security reasons, the password does not appear on
the screen.
6.
If necessary, enter the new password in the "Enter New Password" field.
7.
Enter the new password in the "Re-Enter New Password" field. After
re-entering the new password, a pop-up menu is displayed, asking you to
confirm your selection.
NOTE
To leave the pop-up menu without entering a password, press
the
Esc
key.