HP LH4r HP Netserver LT 6000r Installation Guide - Page 41

Installing Mass Storage Devices

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

4 Installing Mass Storage Devices Introduction The LT 6000r is equipped with one hot-swap SCSI mass storage device cage that holds four low-voltage differential, low profile SCSI devices. The NetServer is also equipped with a built-in CD-ROM and a floppy diskette drive. One SCSI channel, Channel A, supports the hot-swap cage. Another SCSI channel, Channel B, supports external devices via a standard 68-pin wide SCSI connector on the rear panel. NOTE When connecting SCSI devices to the LT 6000r, devices installed in the hot-swap cage are assigned SCSI IDs 00, 01, 02, and 03 from left to right. The embedded controller is assigned ID 07. The SAF-TE processor on the hot-swap cage is assigned ID 05. CAUTION Do not install high-voltage differential (HVD) SCSI devices on the same SCSI channel as SE or LVD devices or the devices will be damaged. Tools Required No tools are required to remove and replace NetServer mass storage devices from the hot-swap cage. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
33
4
Installing Mass Storage Devices
Introduction
The LT 6000r is equipped with one hot-swap SCSI mass storage device cage that
holds four low-voltage differential, low profile SCSI devices. The NetServer is
also equipped with a built-in CD-ROM and a floppy diskette drive.
One SCSI channel, Channel A, supports the hot-swap cage. Another SCSI
channel, Channel B, supports external devices via a standard 68-pin wide SCSI
connector on the rear panel.
NOTE
When connecting SCSI devices to the LT 6000r, devices
installed in the hot-swap cage are assigned SCSI IDs 00, 01,
02, and 03 from left to right. The embedded controller is
assigned ID 07. The SAF-TE processor on the hot-swap cage is
assigned ID 05.
CAUTION
Do not install high-voltage differential (HVD) SCSI devices
on the same SCSI channel as SE or LVD devices or the
devices will be damaged.
Tools Required
No tools are required to remove and replace NetServer mass storage devices from
the hot-swap cage.