HP LH4r HP Netserver LT 6000r Installation Guide - Page 18

Front Panel Console

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Chapter 2 Controls, Indicators, and Ports Front Panel Console Figure 2-2 shows the LT 6000r front panel console. Figure 2-2. Front Panel Console Table 2-1. Front Panel Console Switch and Indicator Definitions Control Description Secure Mode Indicator Locks system keyboard, monitor display, and control panel to prevent unauthorized use. Go to the Setup utility security menu to configure this feature. DC Power Switch and LED 10 Turns the HP NetServer on and off. This switch is under the protective door on the front panel. Push once to turn on, again to turn off. As long as the AC power is connected to the HP NetServer, standby power is present. l If the LED is steady green, then the HP NetServer is powered-up. l If the LED is flashing green, the HP NetServer is in a power-save mode. l If the LED is off, but the two-line display has a message, standby power is present. l If the HP NetServer is set up to go into power-save mode, the power switch is depressed; you must press it for over four seconds to effect a power down.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Chapter 2
Controls, Indicators, and Ports
10
Front Panel Console
Figure 2-2 shows the LT 6000r
front panel console.
Figure 2-2. Front Panel Console
Table 2-1. Front Panel Console Switch and Indicator Definitions
Control
Description
Secure Mode Indicator
Locks system keyboard, monitor display, and control panel to
prevent unauthorized use. Go to the Setup utility security menu
to configure this feature.
DC Power Switch
and LED
Turns the HP NetServer on and off. This switch is under the
protective door on the front panel. Push once to turn on,
again to turn off. As long as the AC power is connected to
the HP NetServer, standby power is present.
If the LED is steady green, then the HP
NetServer is powered-up.
If the LED is flashing green, the HP NetServer is
in a power-save mode.
If the LED is off, but the two-line display has a
message, standby power is present.
If the HP NetServer is set up to go into
power-save mode, the power switch is
depressed; you must press it for over four
seconds to effect a power down.