HP LH4r HP Netserver LT 6000r Installation Guide - Page 121

SCSI Configuration Utility

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

Chapter 10 Configuring the HP NetServer Figure 10-2. System Board Configuration Switch 3. Close the system board access panel and power on the server. 4. Let the server boot. 5. After booting, shut down and power off the server and open the system board access panel. 6. Reset Switch 5 from the ON position to OFF. 7. Close the system board access panel and power on the server. SCSI Configuration Utility NOTE The Symbios Configuration Utility is not available if you leave the NetRAID default (enabled) unchanged. It is only available for LVD SCSI mode. If you need to verify or modify SCSI host adapter settings or if you need low-level format SCSI disks or verify SCSI disk media, run the Symbios Configuration Utility: 1. Power on or reboot the server. 2. During system start-up or reset, simultaneously press [Ctrl] and [C] when the following message appears: Press [Ctrl] [C] to start Symbios Configuration Utility 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Chapter 10
Configuring the HP NetServer
113
Figure 10-2. System Board Configuration Switch
3.
Close the system board access panel and power on the server.
4.
Let the server boot.
5.
After booting, shut down and power off the server and open the system
board access panel.
6.
Reset Switch 5 from the ON position to OFF.
7.
Close the system board access panel and power on the server.
SCSI Configuration Utility
NOTE
The Symbios Configuration Utility is not available if you leave
the NetRAID default (enabled) unchanged. It is only available
for LVD SCSI mode.
If you need to verify or modify SCSI host adapter settings or if you need low-level
format SCSI disks or verify SCSI disk media, run the Symbios Configuration
Utility:
1.
Power on or reboot the server.
2.
During system start-up or reset, simultaneously press [
Ctrl
] and [
C
] when
the following message appears:
Press [Ctrl] [C] to start Symbios Configuration
Utility