HP LH4r HP Netserver LT 6000r Installation Guide - Page 91

Step 3: Mount the LT 6000r in the Rack

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Chapter 8 Mounting the HP NetServer in an HP Rack System/E or Rack System/U Step 3: Mount the LT 6000r in the Rack This step explains how to mount the LT 6000r into the rack. WARNING Ensure that the rack's anti-tip foot is fully extended out of the rack to prevent rack instability while mounting LT 6000r. Failure to do so could result in injury and equipment damage. WARNING To prevent the rack from rolling while you mount the LT 6000r, make sure that the leveler screws on the rack's lower four corners are in firm contact with the floor. 1. Fully extend each of the slide members. The slides lock into position. You cannot push the slides back in the rack without pressing in each slides release latch. See Figure 8-5. Slide members Anti-tip foot Figure 8-5. Extending the Slide Members 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Chapter 8
Mounting the HP NetServer in an HP Rack System/E or Rack System/U
83
Step 3: Mount the LT 6000r in the Rack
This step explains how to mount the LT 6000r into the rack.
WARNING
Ensure that the rack’s anti-tip foot is fully extended out of the
rack to prevent rack instability while mounting LT 6000r.
Failure to do so could result in injury and equipment damage.
WARNING
To prevent the rack from rolling while you mount the
LT 6000r, make sure that the leveler screws on the rack’s
lower four corners are in firm contact with the floor.
1. Fully extend each of the slide members. The slides lock into position. You
cannot push the slides back in the rack without pressing in each slides
release latch. See Figure 8-5.
Slide members
Anti-tip foot
Figure 8-5. Extending the Slide Members