HP LH4r HP Netserver LT 6000r Installation Guide - Page 54

Removing DIMMs

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Chapter 5 DIMM Installing Additional Memory Retaining Clip Notches Keys Retaining Clip Figure 5-2. Inserting a DIMM into Its Socket e. Holding the DIMM 90 degrees to the system board, press the DIMM into the socket until the retaining clips close. If the clips do not close, the DIMM is not inserted correctly. CAUTION Do not rock the DIMM into its socket. Apply firm and even pressure. It a gap exists between the retaining latches and the DIMM, remove and replace the DIMM until no gap exists. 8. Repeat Step 2 to install all of the DIMMs for your memory configuration. 9. If you removed the system board assembly from the NetServer, replace it now. 10. Close the system board access panel according to the instructions in Chapter 3, Opening and Closing the HP NetServer. 11. Replace the power cords and cables. 12. Restore the NetServer to normal operation. Removing DIMMs You may need to remove a DIMM to downsize your memory configuration or to replace a defective DIMM. (Refer to Figure 5-2.) 1. Log off all users, and shut down the network operating system according to your NOS instructions. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Chapter 5
Installing Additional Memory
46
DIMM
Notches
Keys
Retaining
Clip
Retaining
Clip
Figure 5-2. Inserting a DIMM into Its Socket
e.
Holding the DIMM 90 degrees to the system board, press the DIMM
into the socket until the retaining clips close. If the clips do not close,
the DIMM is not inserted correctly.
CAUTION
Do not rock the DIMM into its socket. Apply firm and even
pressure. It a gap exists between the retaining latches and the
DIMM, remove and replace the DIMM until no gap exists.
8.
Repeat Step 2 to install all of the DIMMs for your memory configuration.
9.
If you removed the system board assembly from the NetServer, replace it
now.
10.
Close the system board access panel according to the instructions in
Chapter 3,
Opening and Closing the HP NetServer
.
11.
Replace the power cords and cables.
12.
Restore the NetServer to normal operation.
Removing DIMMs
You may need to remove a DIMM to downsize your memory configuration or to
replace a defective DIMM. (Refer to Figure 5-2.)
1.
Log off all users, and shut down the network operating system according to
your NOS instructions.