HP LH4r HP Netserver LT 6000r Installation Guide - Page 63

see the sub Installing an Accessory Board into Slot 1.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Chapter 6 Installing Additional Boards Figure 6-3. Removing the PCI Slot Cover (Locking Levers and Retainers Shown) 8. Before installing an accessory board: ◊ Verify that there is no extender attached to it, especially if it is a full-length board. ◊ If the board has a extender attached to it, remove the extender before installing the board. 9. Align the full length of the board with its slot and position it into the slot. NOTE For instructions on installing a PCI accessory board in Slot 1, see the subsection "Installing an Accessory Board into Slot 1." CAUTION Do not bend the accessory board when installing it. All accessory boards are held in place with the PCI lever and retainer. Full-size boards are supported when seated in the card guides. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Chapter 6
Installing Additional Boards
55
Figure 6-3. Removing the PCI Slot Cover
(Locking Levers and Retainers Shown)
8.
Before installing an accessory board:
◊
Verify that there is no extender attached to it, especially if it is a
full-length board.
◊
If the board has a extender attached to it, remove the extender before
installing the board.
9.
Align the full length of the board with its slot and position it into the slot.
NOTE
For instructions on installing a PCI accessory board in Slot 1,
see the subsection "Installing an Accessory Board into Slot 1."
CAUTION
Do not bend the accessory board when installing it.
All accessory boards are held in place with the PCI lever and
retainer. Full-size boards are supported when seated in the
card guides.