HP Latex 3200 Site Preparation Guide - Page 7

Return the site preparation checklist

Get HP Latex 3200 PDF manuals and user guides View all HP Latex 3200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

If you have bought non-HP RIP software for your printer: NOTE: This guide does not provide information about your RIP solution. ● You must install the RIP on a suitable computer and ensure that it is fully functional by the agreed date of printer installation. ● For full functionality, you are recommended to ensure that the computer is connected to the Internet. ● You must ensure that a RIP specialist and a network specialist are present on the agreed date of printer installation. Networking You are responsible for all networking requirements, and you must complete the following tasks: NOTE: In order to perform remote support, the printer must have access to the internet using the LAN connection. ● Have an adequate network ready for the day of installation. See Computer and networking requirements on page 19. ● Provide a CAT-6 LAN cable to connect the printer to your LAN on the day of installation. Printing supplies for testing and training You are responsible for providing the following printing supplies: ● Seven ink cartridges, for the six colors and the optimizer (no cartridges are supplied with the printer) NOTE: In addition, you are recommended to have a second set of seven ink cartridges, four printheads, and one HP 881 Latex Cleaning Roll, in case any replacements are needed. ● Compressed air supply for the pneumatic spindle. See Air pressure supply on page 12. ● Some rolls of substrate for printing; preferably the substrate type that you plan to use most in future ● To test dual-roll printing, two rolls of max 1524 mm (63 in), max weight per roll 80 kg (176 lb). Return the site preparation checklist The checklist must be completed and returned to your reseller or service representative a minimum of two weeks before the day of installation. NOTE: Any delays during installation that are caused by an unprepared site will be charged to the customer. Take care that your site is properly prepared to ensure a smooth and easy installation. Recycle the disposable ink bag and HP 881 Latex Cleaning Roll These items require disposal according to local regulations. For further information, please refer to the SDS document about your printer's ink, available from http://www.hp.com/hpinfo/community/environment/ productinfo/psis_inkjet.htm. Recycle the printheads The printheads require disposal according to local regulations. For further information, please refer to the MSDS document about your printer's ink, available from http://www.hp.com/hpinfo/community/environment/ productinfo/psis_inkjet.htm. Within some countries covered by the 'HP Planet Partners Returns', HP is offering a recycling program. For full details of this program, see http://www.hp.com/recycle/. ENWW Customer responsibility 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
If you have bought non-HP RIP software for your printer:
NOTE:
This guide does not provide information about your RIP solution.
●
You must install the RIP on a suitable computer and ensure that it is fully functional by the agreed date of
printer installation.
●
For full functionality, you are recommended to ensure that the computer is connected to the Internet.
●
You must ensure that a RIP specialist and a network specialist are present on the agreed date of printer
installation.
Networking
You are responsible for all networking requirements, and you must complete the following tasks:
NOTE:
In order to perform remote support, the printer must have access to the internet using the LAN
connection.
●
Have an adequate network ready for the day of installation. See
Computer and networking requirements
on page
19
.
●
Provide a CAT-6 LAN cable to connect the printer to your LAN on the day of installation.
Printing supplies for testing and training
You are responsible for providing the following printing supplies:
●
Seven ink cartridges, for the six colors and the optimizer (no cartridges are supplied with the printer)
NOTE:
In addition, you are recommended to have a second set of seven ink cartridges, four printheads,
and one HP 881 Latex Cleaning Roll, in case any replacements are needed.
●
Compressed air supply for the pneumatic spindle. See
Air pressure supply
on page
12
.
●
Some rolls of substrate for printing; preferably the substrate type that you plan to use most in future
●
To test dual-roll printing, two rolls of max 1524 mm (63 in), max weight per roll 80 kg (176 lb).
Return the site preparation checklist
The checklist must be completed and returned to your reseller or service representative a minimum of two
weeks before the day of installation.
NOTE:
Any delays during installation that are caused by an unprepared site will be charged to the customer.
Take care that your site is properly prepared to ensure a smooth and easy installation.
Recycle the disposable ink bag and HP 881 Latex Cleaning Roll
These items require disposal according to local regulations. For further information, please refer to the SDS
document about your printer's ink, available from
hpinfo/community/environment/
productinfo/psis_inkjet.htm
.
Recycle the printheads
The printheads require disposal according to local regulations. For further information, please refer to the MSDS
document about your printer's ink, available from
hpinfo/community/environment/
productinfo/psis_inkjet.htm
. Within some countries covered by the ‘HP Planet Partners Returns’, HP is offering a
recycling program. For full details of this program, see
recycle/
.
ENWW
Customer responsibility
3