HP ProBook 6465b HP ProBook 6465b Notebook PC - Maintenance and Service Guide - Page 54

replace the screws, When replacing the display panel, after connecting the display cable

Get HP ProBook 6465b PDF manuals and user guides View all HP ProBook 6465b manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

8. If it is necessary to replace the display panel, remove the four Phillips PM2.5×5.0 screws (1) at the bottom of the display panel. 9. Remove the two broadhead Phillips PM2.0×4.0 screws (2) at the top of the display panel. 10. Pivot the display panel upward until it sits at a 90 degree angle (3). 11. Disconnect the display panel cable from the back of the display panel (1). 12. Remove the four Phillips PM2.5×5.0 screws (2) that secure the display panel to the brackets. 13. Slide the display panel up and out of the hinges (3). Reverse this procedure to reassemble and install the display assembly components. When replacing the display panel, after connecting the display cable, slide the panel into the bracket (1), replace the screws (2), and then rotate the panel assembly downward so it lies flat in the enclosure (3). Make sure to insert the display panel brackets into the notches in the corners of the display enclosure (4). 46 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
8.
If it is necessary to replace the display panel, remove the four Phillips PM2.5×5.0 screws
(1)
at
the bottom of the display panel.
9.
Remove the two broadhead Phillips PM2.0×4.0 screws
(2)
at the top of the display panel.
10.
Pivot the display panel upward until it sits at a 90 degree angle
(3)
.
11.
Disconnect the display panel cable from the back of the display panel
(1)
.
12.
Remove the four Phillips PM2.5×5.0 screws
(2)
that secure the display panel to the brackets.
13.
Slide the display panel up and out of the hinges
(3)
.
Reverse this procedure to reassemble and install the display assembly components.
When replacing the display panel, after connecting the display cable, slide the panel into the bracket
(1)
, replace the screws
(2)
, and then rotate the panel assembly downward so it lies flat in the
enclosure
(3)
. Make sure to insert the display panel brackets into the notches in the corners of the
display enclosure
(4)
.
46
Chapter 4
Removal and replacement procedures