HP ProLiant MicroServer Gen8 HP ProLiant MicroServer Gen8 Maintenance and Serv - Page 46

Integrated power supply

Get HP ProLiant MicroServer Gen8 PDF manuals and user guides View all HP ProLiant MicroServer Gen8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Integrated power supply WARNING: To reduce the risk of personal injury from hot surfaces, allow the power supply or power supply blank to cool before touching it. To remove the component: 1. Power down the server (on page 23). 2. Disconnect the power cord from the AC source. 3. Disconnect the power cord from the server. 4. Remove the chassis cover (on page 26). 5. If installed, remove the optical drive ("Optical drive" on page 33). 6. Disconnect all power supply cables: a. Disconnect the PSU P1 cable from the system board, and then release it from the left-side chassis cable clip. b. If installed, remove the optical drive ("Optical drive" on page 33). c. Disconnect the PSU P3 cable from the 4-pin optical drive power cable. d. Disconnect the PSU P2 cable from the 4-pin drive power cable. 7. Remove the power supply. a. Remove the three screws from the rear side of the power supply. b. Remove the one screw from the front side of the power supply. Removal and replacement procedures 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Removal and replacement procedures
46
Integrated power supply
WARNING:
To reduce the risk of personal injury from hot surfaces, allow the power supply or
power supply blank to cool before touching it.
To remove the component:
1.
Power down the server (on page
23
).
2.
Disconnect the power cord from the AC source.
3.
Disconnect the power cord from the server.
4.
Remove the chassis cover (on page
26
).
5.
If installed, remove the optical drive ("
Optical drive
" on page
33
).
6.
Disconnect all power supply cables:
a.
Disconnect the PSU P1 cable from the system board, and then release it from the left-side chassis
cable clip.
b.
If installed, remove the optical drive ("
Optical drive
" on page
33
).
c.
Disconnect the PSU P3 cable from the 4-pin optical drive power cable.
d.
Disconnect the PSU P2 cable from the 4-pin drive power cable.
7.
Remove the power supply.
a.
Remove the three screws from the rear side of the power supply.
b.
Remove the one screw from the front side of the power supply.