HP ProLiant MicroServer Gen8 HP ProLiant MicroServer Gen8 Maintenance and Serv - Page 48

DIMMs, General DIMM slot population guidelines - power consumption

Page 48 highlights

8. Remove the expansion board. To replace the component, reverse the removal procedure. DIMMs General DIMM slot population guidelines • The server supports a maximum of 16 GB memory using two 8 GB single-rank or dual-rank UDIMMs. • The server supports up to 1600 MT/s ECC UDIMMs. • LV DIMMs operate at 1.35 V instead of the 1.5 V for standard DDR3 DIMMs. LV DIMMs can be installed in this server, but the system does not recognize the reduced power consumption feature. It will be treated as a standard DDR3 DIMM. • Memory speed depends on the type of processor and the number of DIMMs installed in the server. Installed DIMMs can operate at either 1600 MT/s or 1333 MT/s. For more information, see the technical specification of the installed processor. • When installing DIMMs, populate the 1-A DIMM slot first and, then the 2-B slot. • For DIMM spare replacement, install the DIMMs per slot number as instructed by the system software. • Use only HP qualified DIMMs. • The server does not support: o RDIMMs o Non-ECC UDIMMs • The minimum DIMM requirement to make this server bootable is a DIMM in either DIMM slot. For detailed memory configuration rules and guidelines, use the Online DDR3 Memory Configuration Tool on the HP website (http://www.hp.com/go/ddr3memory-configurator). Removal and replacement procedures 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87

Removal and replacement procedures
48
8.
Remove the expansion board.
To replace the component, reverse the removal procedure.
DIMMs
General DIMM slot population guidelines
The server supports a maximum of 16 GB memory using two 8 GB single-rank or dual-rank UDIMMs.
The server supports up to 1600 MT/s ECC UDIMMs.
LV DIMMs operate at 1.35 V instead of the 1.5 V for standard DDR3 DIMMs. LV DIMMs can be
installed in this server, but the system does not recognize the reduced power consumption feature. It will
be treated as a standard DDR3 DIMM.
Memory speed depends on the type of processor and the number of DIMMs installed in the server.
Installed DIMMs can operate at either 1600 MT/s or 1333 MT/s. For more information, see the
technical specification of the installed processor.
When installing DIMMs, populate the 1-A DIMM slot first and, then the 2-B slot.
For DIMM spare replacement, install the DIMMs per slot number as instructed by the system software.
Use only HP qualified DIMMs.
The server does not support:
o
RDIMMs
o
Non-ECC UDIMMs
The minimum DIMM requirement to make this server bootable is a DIMM in either DIMM slot.
For detailed memory configuration rules and guidelines, use the Online DDR3 Memory Configuration Tool
on the HP website (
).