HP ProLiant MicroServer Gen8 HP ProLiant MicroServer Gen8 Maintenance and Serv - Page 49

Removing a DIMM, Heatsink

Get HP ProLiant MicroServer Gen8 PDF manuals and user guides View all HP ProLiant MicroServer Gen8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Removing a DIMM 1. Power down the server (on page 23). 2. Disconnect the power cord from the AC source. 3. Disconnect the power cord from the server. 4. Remove the chassis cover (on page 26). 5. Open the DIMM slot latches. 6. Remove the DIMM. To replace the component, reverse the removal procedure. Heatsink To remove the component: 1. Power down the server (on page 23). 2. Disconnect the power cord from the AC source. 3. Disconnect the power cord from the server. 4. Remove the chassis cover (on page 26). 5. Remove the system board assembly (on page 28). WARNING: To reduce the risk of personal injury from hot surfaces, allow the heatsink to cool before touching it. CAUTION: Heatsink retaining screws should be tightened or loosened in diagonally opposite pairs (in an "X" pattern). Do not overtighten the screws as this can damage the board, connectors, or screws. Use the wrench supplied with the system to reduce the possibility of overtightening the screws. 6. Remove the heatsink: a. Loosen one pair of diagonally opposite screws halfway, and then loosen the other pair of screws. Removal and replacement procedures 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Removal and replacement procedures
49
Removing a DIMM
1.
Power down the server (on page
23
).
2.
Disconnect the power cord from the AC source.
3.
Disconnect the power cord from the server.
4.
Remove the chassis cover (on page
26
).
5.
Open the DIMM slot latches.
6.
Remove the DIMM.
To replace the component, reverse the removal procedure.
Heatsink
To remove the component:
1.
Power down the server (on page
23
).
2.
Disconnect the power cord from the AC source.
3.
Disconnect the power cord from the server.
4.
Remove the chassis cover (on page
26
).
5.
Remove the system board assembly (on page
28
).
WARNING:
To reduce the risk of personal injury from hot surfaces, allow the heatsink to cool
before touching it.
CAUTION:
Heatsink retaining screws should be tightened or loosened in diagonally opposite
pairs (in an "X" pattern). Do not overtighten the screws as this can damage the board, connectors,
or screws. Use the wrench supplied with the system to reduce the possibility of overtightening the
screws.
6.
Remove the heatsink:
a.
Loosen one pair of diagonally opposite screws halfway, and then loosen the other pair of screws.