HP ProLiant WS460c HP ProLiant WS460c Gen8 Workstation Blade with WS460c Graph - Page 40

the same enclosure. These labels are replaceable with any commonly available tape or label,

Get HP ProLiant WS460c PDF manuals and user guides View all HP ProLiant WS460c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

If the screws do not have Nylok coating, or are used, add Loctite 242 Threadlocker 3~5 threads from the tip. 7. Torque both front plate screws to 3.0~3.5 in-lbf. IMPORTANT: Ensure that air flow impedance control labels cover the three openings on each end of the I/O plate. These labels control the air flow into the GRID card and balance the air flow to adjacent blades. Using the card in the expansion blade without implementing this measure might potentially result in unexpected host shutdown of the host blade and/or nearby blades in the same enclosure. These labels are replaceable with any commonly available tape or label, as long as the tape or label covers the hole as shown and has construction to withstand the air flow without deforming or falling off when powered off. After installation, always ensure that the labels are not removed or detached. Removal and replacement procedures 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Removal and replacement procedures
40
If the screws do not have Nylok coating, or are used, add Loctite 242 Threadlocker 3~5 threads from
the tip.
7.
Torque both front plate screws to 3.0~3.5 in-lbf.
IMPORTANT:
Ensure that air flow impedance control labels cover the three openings on each
end of the I/O plate. These labels control the air flow into the GRID card and balance the air flow
to adjacent blades. Using the card in the expansion blade without implementing this measure
might potentially result in unexpected host shutdown of the host blade and/or nearby blades in
the same enclosure. These labels are replaceable with any commonly available tape or label, as
long as the tape or label covers the hole as shown and has construction to withstand the air flow
without deforming or falling off when powered off. After installation, always ensure that the labels
are not removed or detached.