HP ProLiant WS460c HP ProLiant WS460c Gen8 Workstation Blade with WS460c Graph - Page 79

Server blade release lever assembly

Get HP ProLiant WS460c PDF manuals and user guides View all HP ProLiant WS460c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

18. Install the hard drives ("Drive" on page 41). 19. Install the hard drive blanks ("Drive blank" on page 41). 20. Install the access panel ("Access panel" on page 28). 21. Install the workstation blade. After you replace the system board, you must re-enter the workstation blade serial number and the product ID. 1. During the workstation blade startup sequence, press the F9 key to access RBSU. 2. Select the Advanced Options menu. 3. Select Service Options. 4. Select Serial Number. The following warning appears: Warning: The serial number should ONLY be modified by qualified service personnel. This value should always match the serial number located on the chassis. 5. Press the Enter key to clear the warning. 6. Enter the serial number and press the Enter key. 7. Select Product ID. The following warning appears: Warning: The Product ID should ONLY be modified by qualified service personnel. This value should always match the Product ID located on the chassis. 8. Enter the product ID and press the Enter key. 9. Press the Esc key to close the menu. 10. Press the Esc key to exit RBSU. 11. Press the F10 key to confirm exiting RBSU. The workstation blade automatically reboots. Server blade release lever assembly To remove the component: 1. Power down the workstation blade (on page 26). 2. Remove the workstation blade (on page 28). 3. Remove the access panel ("Access panel" on page 28). 4. Remove all hard drives ("Drive" on page 41). 5. Remove all hard drive blanks ("Drive blank" on page 41). 6. Remove all DIMM baffles ("DIMM baffles" on page 43). 7. Remove all DIMMs ("DIMMs" on page 44). 8. Disconnect the capacitor pack cabling, if connected ("FBWC capacitor pack cabling" on page 97). 9. Remove the SAS controller ("SAS controller" on page 54). 10. Remove the heatsink blank, if installed ("Heatsink blank" on page 46). 11. Remove the front panel/hard drive cage assembly ("Front panel/drive cage assembly" on page 66). Removal and replacement procedures 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Removal and replacement procedures
79
18.
Install the hard drives ("
Drive
" on page
41
).
19.
Install the hard drive blanks ("
Drive blank
" on page
41
).
20.
Install the access panel ("
Access panel
" on page
28
).
21.
Install the workstation blade.
After you replace the system board, you must re-enter the workstation blade serial number and the product
ID.
1.
During the workstation blade startup sequence, press the
F9
key to access RBSU.
2.
Select the
Advanced Options
menu.
3.
Select
Service Options
.
4.
Select
Serial Number
. The following warning appears:
Warning: The serial number should ONLY be modified by qualified service
personnel. This value should always match the serial number located on the
chassis.
5.
Press the
Enter
key to clear the warning.
6.
Enter the serial number and press the
Enter
key.
7.
Select
Product ID
. The following warning appears:
Warning: The Product ID should ONLY be modified by qualified service
personnel. This value should always match the Product ID located on the
chassis.
8.
Enter the product ID and press the
Enter
key.
9.
Press the
Esc
key to close the menu.
10.
Press the
Esc
key to exit RBSU.
11.
Press the
F10
key to confirm exiting RBSU. The workstation blade automatically reboots.
Server blade release lever assembly
To remove the component:
1.
Power down the workstation blade (on page
26
).
2.
Remove the workstation blade (on page
28
).
3.
Remove the access panel ("
Access panel
" on page
28
).
4.
Remove all hard drives ("
Drive
" on page
41
).
5.
Remove all hard drive blanks ("
Drive blank
" on page
41
).
6.
Remove all DIMM baffles ("
DIMM baffles
" on page
43
).
7.
Remove all DIMMs ("
DIMMs
" on page
44
).
8.
Disconnect the capacitor pack cabling, if connected ("
FBWC capacitor pack cabling
" on page
97
).
9.
Remove the SAS controller ("
SAS controller
" on page
54
).
10.
Remove the heatsink blank, if installed ("
Heatsink blank
" on page
46
).
11.
Remove the front panel/hard drive cage assembly ("
Front panel/drive cage assembly
" on page
66
).