HP ProLiant WS460c HP ProLiant WS460c Gen8 Workstation Blade with WS460c Graph - Page 82

Install the SAS controller

Get HP ProLiant WS460c PDF manuals and user guides View all HP ProLiant WS460c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

3. Align the system board, and then slide it into place inside the base pan. 4. While holding the system board in place, turn the base pan on the side and install the two screws on the bottom of the base pan. 5. Place the workstation blade on a flat level surface. IMPORTANT: Install all components in the same configuration prior to removing the system board. 6. Install the front panel/drive cage assembly ("Front panel/drive cage assembly" on page 66). 7. Install the heatsink blank ("Heatsink blank" on page 46). 8. Install the SAS controller ("SAS controller" on page 54). 9. Install and route the cables for all capacitor packs. For more information on routing the cables, see "FBWC capacitor pack cabling (on page 97)." 10. Install all DIMMs ("DIMMs" on page 44). 11. Install all DIMM baffles ("DIMM baffles" on page 43). Removal and replacement procedures 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Removal and replacement procedures
82
3.
Align the system board, and then slide it into place inside the base pan.
4.
While holding the system board in place, turn the base pan on the side and install the two screws on the
bottom of the base pan.
5.
Place the workstation blade on a flat level surface.
IMPORTANT:
Install all components in the same configuration prior to removing the system
board.
6.
Install the front panel/drive cage assembly ("
Front panel/drive cage assembly
" on page
66
).
7.
Install the heatsink blank ("
Heatsink blank
" on page
46
).
8.
Install the SAS controller ("
SAS controller
" on page
54
).
9.
Install and route the cables for all capacitor packs. For more information on routing the cables, see
"FBWC capacitor pack cabling (on page
97
)."
10.
Install all DIMMs ("
DIMMs
" on page
44
).
11.
Install all DIMM baffles ("
DIMM baffles
" on page
43
).