HP StoreOnce D2D4324 HP StoreOnce VSA user guide (TC458-96002, July 2013) - Page 43

Status tab, net show config, Node Specific Parameters, Network Virtual Data IP

Get HP StoreOnce D2D4324 PDF manuals and user guides View all HP StoreOnce D2D4324 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

2. Locate its VIF IP in the System Information. To identify the VIF address from the StoreOnce CLI (command line interface) Use the net show config command and locate the Node Specific Parameters. You are looking for the Network Virtual Data IP entries under each node. (The network template that was applied at system installation determines whether it is a 10GbE or 1GbE network.) The following example is an extract from the output of the net show config command. # net show config External Network Configuration Template 1 Management on (2) 1Gb ports (bonded), Data/Replication on (2) 10Gb ports (bonded) Virtual Management Console IP Address: 16.26.xxx.xxx Node Specific Parameters Node 1: 1GbE Network Physical IP (HP Service Only): 16.26.xxx.xxx 10GbE Network Physical IP (HP Service Only): 172.16.7.199 10GbE Network Virtual Data IP: 172.16.7.200 Node 2: 1GbE Network Physical IP (HP Service Only): 16.26.xxx.xxx 10GbE Network Physical IP (HP Service Only): 172.16.7.201 10GbE Network Virtual Data IP: 172.16.7.202 Status tab Status tab 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
2.
Locate its
VIF IP
in the
System Information
.
To identify the VIF address from the StoreOnce CLI (command line interface)
Use the
net show config
command and locate the
Node Specific Parameters
.
You are looking for the
Network Virtual Data IP
entries under each node. (The network
template that was applied at system installation determines whether it is a 10GbE or 1GbE network.)
The following example is an extract from the output of the
net show config
command.
# net show config
External Network Configuration
------------------------------
Template 1
Management on (2) 1Gb ports (bonded), Data/Replication on (2) 10Gb ports (bonded)
Virtual Management Console IP Address: 16.26.xxx.xxx
Node Specific Parameters
------------------------
Node 1:
1GbE Network Physical IP (HP Service Only): 16.26.xxx.xxx
10GbE Network Physical IP (HP Service Only): 172.16.7.199
10GbE Network Virtual Data IP: 172.16.7.200
Node 2:
1GbE Network Physical IP (HP Service Only): 16.26.xxx.xxx
10GbE Network Physical IP (HP Service Only): 172.16.7.201
10GbE Network Virtual Data IP: 172.16.7.202
Status tab
Status tab
43