HP Surestore 125ex Hewlett-Packard SureStore 125ex Optical Jukebox User&#1 - Page 22

Onnecting, Ukebox, Eripheral

Get HP Surestore 125ex - Optical Jukebox PDF manuals and user guides View all HP Surestore 125ex manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

1 NEXT PREVIOUS JUMP CONTENTS INDEX SETTING UP THE JUKEBOX CONNECTING THE JUKEBOX AS THE ONLY PERIPHERAL The default IDs for the jukebox are as follows. Check to see if there will be any conflicts in this installation. Autochanger (jukebox robotics) = 3 Drive 1 = 4 Drive 2 = 5 (if installed) NOTE: If any of the autochanger/drive IDs are already being used, you can either change IDs used by the host bus adapter or another device on the bus, or you can change the autochanger/drive IDs. If you choose to change the IDs of devices other than the autochanger and/or drives, do it now (before you begin cabling). Refer to your host and host bus adapter documentation. If you will be changing the IDs of the autochanger or the drives, you will be given an opportunity to do this in the installation steps that follow. 1. Ensure that the mailslot shipping bracket and the shipping screw are removed. NOTE: If you will be changing SCSI IDs in the host, finish changing them before doing the next step. See the previous NOTE. 2. Ensure that your host computer is OFF and the jukebox standby/on switch is in the STANDBY position. The jukebox standby/on switch is in STANDBY when the STANDBY side of the switch is depressed. The switch is shown by "2" on Figure 1-1. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
1
S
ETTING
UP
THE
J
UKEBOX
1
11
NEXT
PREVIOUS
JUMP
CONTENTS
INDEX
C
ONNECTING
THE
J
UKEBOX
AS
THE
O
NLY
P
ERIPHERAL
The default IDs for the jukebox are as follows.
Check to see if there will be any conflicts in this installation.
Autochanger (jukebox robotics) = 3
Drive 1 = 4
Drive 2 = 5 (if installed)
NOTE:
If any of the autochanger/drive IDs are already being used, you can either change IDs used by the host bus adapter or
another device on the bus, or you can change the autochanger/drive IDs.
If you choose to change the IDs of devices other than the autochanger and/or drives, do it now (before you begin
cabling). Refer to your host and host bus adapter documentation.
If you will be changing the IDs of the autochanger or the drives, you will be given an opportunity to do this in the
installation steps that follow.
1.
Ensure that the mailslot shipping bracket and the shipping screw are removed.
NOTE:
If you will be changing SCSI IDs in the host, finish changing them before doing the next step. See the previous NOTE.
2.
Ensure that your host computer is OFF and the jukebox standby/on switch is in the STANDBY position.
The jukebox standby/on switch is in STANDBY when the STANDBY side of the switch is depressed. The switch is
shown by “2” on
Figure 1-1
.