HP Surestore 125ex Hewlett-Packard SureStore 125ex Optical Jukebox User&#1 - Page 27

Onnecting, Djusting, Urning, Ukebox

Get HP Surestore 125ex - Optical Jukebox PDF manuals and user guides View all HP Surestore 125ex manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

1 NEXT PREVIOUS JUMP CONTENTS INDEX SETTING UP THE JUKEBOX CONNECTING POWER, ADJUSTING IDS, AND TURNING THE JUKEBOX ON NOTE: If you are changing SCSI IDs on the host bus adapter to avoid conflicts, change the IDs before turning host power OFF. If you are changing IDs on one (or two) of this jukebox to avoid conflicts, the following steps include this option. 1. Ensure that your host computer is OFF and the jukebox standby/on switch is in the STANDBY position. 2. Plug the socket end of the power cord into the power port on the rear of the jukebox (see "1" on Figure 1-1). Use the power cord supplied with the jukebox. 3. Plug the other end of the power cord into a grounded electrical outlet. Caution: Placing the standby/on switch to STANDBY does not remove all power from the jukebox. To remove all power (including primary power) you must pull the jukebox power plug from the wall/floor receptacle. 4. Press the jukebox standby/on switch to ON. NOTE: If you are connecting two jukeboxes, place both jukeboxes to ON. The remaining steps apply to both jukeboxes. 5. Initially, TESTING appears in the display window on the front of the jukebox. Once the poweron test completes (approximately 1.5 minutes), READY displays. NOTE: If FAIL 1 displays, the poweron test was not successful. Feel under the chassis at the location shown in Figure 1-3 to ensure that the shipping screw was removed. If the shipping screw was removed, refer to "Troubleshooting" in Chapter 3. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
1
S
ETTING
UP
THE
J
UKEBOX
1
16
NEXT
PREVIOUS
JUMP
CONTENTS
INDEX
C
ONNECTING
P
OWER
, A
DJUSTING
ID
S
,
AND
T
URNING
THE
J
UKEBOX
O
N
NOTE:
If you are changing SCSI IDs on the host bus adapter to avoid conflicts, change the IDs before turning host power
OFF.
If you are changing IDs on one (or two) of this jukebox to avoid conflicts, the following steps include this option.
1.
Ensure that your host computer is OFF and the jukebox standby/on switch is in the STANDBY position.
2.
Plug the socket end of the power cord into the power port on the rear of the jukebox (see “1” on
Figure 1-1
). Use the
power cord supplied with the jukebox.
3.
Plug the other end of the power cord into a grounded electrical outlet.
Caution:
Placing the standby/on switch to STANDBY does not remove all power from the jukebox. To remove all power (including primary
power) you must pull the jukebox power plug from the wall/floor receptacle.
4.
Press the jukebox standby/on switch to ON.
NOTE:
If you are connecting two jukeboxes, place both jukeboxes to ON.
The remaining steps apply to both jukeboxes.
5.
Initially,
TESTING
appears in the display window on the front of the jukebox. Once the poweron test completes
(approximately 1.5 minutes),
READY
displays.
NOTE:
If
FAIL 1
displays, the poweron test was not successful. Feel under the chassis at the location shown in
Figure 1-3
to
ensure that the shipping screw was removed. If the shipping screw was removed, refer to
“Troubleshooting”
in Chapter
3.