HP Surestore 125ex Hewlett-Packard SureStore 125ex Optical Jukebox User&#1 - Page 70

Hanging, Ptical

Get HP Surestore 125ex - Optical Jukebox PDF manuals and user guides View all HP Surestore 125ex manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

3 NEXT PREVIOUS JUMP CONTENTS INDEX OPERATING THE JUKEBOX NOTE: CONFLICT displays if you attempt to set the jukebox controller and a drive to the same ID. Repeat the procedure and reset one of the IDs to another, non-conflicting ID. NOTE: After you change an ID you may have to restart your host computer for the new ID to be recognized. Caution: Do not turn power to STANDBY in this jukebox until you are sure the SCSI bus is inactive. Removing power from a SCSI peripheral when the bus is active can result in data loss and/or indeterminate bus states. Check your host system manuals for information about checking the SCSI bus status. 7. Switch the jukebox standby/on switch to STANDBY, the back to ON to save the new SCSI ID in jukebox memory. CHANGING AN OPTICAL DRIVE ID Start with READY or SECURE in the display. 1. Press NEXT until SCSI ID * displays. 2. Press ENTER. AC ID * displays. ("AC" is the "jukebox controller.") 3. Press NEXT until DRV 1 ID * or DRV 2 ID * (if your jukebox has two drives) displays. 4. Press ENTER. DRV # ID? displays, where "#" is the number of the drive you selected in step 3 and "?" is the ID to which your selected drive is currently set. 5. Press NEXT until the ID you want displays. 6. Press ENTER. SET # (# is a number from 0-7) displays briefly and then DRV # ID # displays again. The ID you chose is now set. 7. Press CANCEL two times to return to the READY state. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
3
O
PERATING
THE
J
UKEBOX
3
31
NEXT
PREVIOUS
JUMP
CONTENTS
INDEX
NOTE:
CONFLICT
displays if you attempt to set the jukebox controller and a drive to the same ID. Repeat the procedure and
reset one of the IDs to another, non-conflicting ID.
NOTE:
After you change an ID you may have to restart your host computer for the new ID to be recognized.
Caution:
Do not turn power to STANDBY in this jukebox until you are sure the SCSI bus is inactive. Removing power from a SCSI
peripheral when the bus is active can result in data loss and/or indeterminate bus states. Check your host system manuals for
information about checking the SCSI bus status.
7.
Switch the jukebox standby/on switch to STANDBY, the back to ON to save the new SCSI ID in jukebox memory.
C
HANGING
AN
O
PTICAL
D
RIVE
ID
Start with
READY
or
SECURE
in the display.
1.
Press
NEXT
until
SCSI ID *
displays.
2.
Press
ENTER
.
AC ID *
displays. (“
AC
” is the “jukebox controller.”)
3.
Press
NEXT
until
DRV 1 ID *
or
DRV 2 ID *
(if your jukebox has two drives) displays.
4.
Press
ENTER
.
DRV # ID?
displays, where “
#
” is the number of the drive you selected in step 3 and “
?
” is the ID to
which your selected drive is currently set.
5.
Press
NEXT
until the ID you want displays.
6.
Press
ENTER
.
SET #
(
#
is a number from 0-7) displays briefly and then
DRV # ID #
displays again. The ID you
chose is now set.
7.
Press
CANCEL
two times to return to the
READY
state.