HP Tc2120 HP Server Ultra 3 SCSI Host Bus Adapter Installation and Configurati - Page 25

Microsoft Windows NT Installation, Installing the Driver When Installing WindowsNT

Page 25 highlights

3 Microsoft Windows NT Installation This chapter explains how to install the HP Ultra3 Family Manager Set driver adpu160m.sys for Windows NT. NOTE the tc2120 does not support NT4.0. If you are performing a first time Windows NT installation, see "Installing the Driver When Windows NT is Already Installed" in the next section. If Windows NT is already installed in your system, see "Installing the Driver When Windows NT is Already Installed" on page 20. Installing the Driver When Installing Windows NT The adpu160m.sys driver is not embedded on the Windows NT 4.0 installation disks (or CD-ROM) and must be added during Windows NT installation. Completing a Fresh Windows NT 4.0 Installation From Floppy Disk 1. Start your system with the Windows NT Boot Disk in the floppy disk drive. 2. When prompted, insert disk #2 in your floppy disk drive. After a few moments you will see a blue screen. To set up Windows NT now, press Enter. 3. Press S to skip auto-detection of your SCSI host adapter. 4. Press S again to specify an additional device. 5. Press Enter to select Others; insert the HP Ultra3 Family Manager Set disk for Windows NT into your floppy disk drive. 6. Using the arrow keys, select the following driver and press Enter: Adaptec Ultra3 PCI SCSI Controller (NT4.0) 7. To add other host adapters, press S and repeat from Step 5 for each additional adapter and insert the appropriate driver disk. 8. Press Enter to continue with the Windows NT operating system setup. Follow the instructions on-screen and in the Windows NT documentation to complete the installation. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78

19
This chapter explains how to install the HP Ultra3 Family Manager Set driver
<File
Name>
adpu160m.sys for Windows NT.
NOTE the tc2120 does not support NT4.0.
If you are performing a first time Windows NT installation, see
“Installing the
Driver When Windows NT is Already Installed”
in the next section. If Windows NT
is already installed in your system, see
“Installing the Driver When Windows NT is
Already Installed”
on page 20.
Installing the Driver When Installing
Windows NT
The
<File Name>
adpu160m.sys driver is not embedded on the Windows NT 4.0
installation disks (or CD-ROM) and must be added during Windows NT installation.
Completing a Fresh Windows NT 4.0 Installation From Floppy
Disk
1.
Start your system with the Windows NT Boot Disk in the floppy disk drive.
2.
When prompted, insert disk #2 in your floppy disk drive. After a few moments
you will see a blue screen. To set up Windows NT now, press Enter.
3.
Press S to skip auto-detection of your SCSI host adapter.
4.
Press S again to specify an additional device.
5.
Press Enter to select Others; insert the HP Ultra3 Family Manager Set disk for
Windows NT into your floppy disk drive.
6.
Using the arrow keys, select the following driver and press Enter:
Adaptec Ultra3 PCI SCSI Controller (NT4.0)
7.
To add other host adapters, press S and repeat from
Step 5
for each additional
adapter and insert the appropriate driver disk.
8.
Press Enter to continue with the Windows NT operating system setup. Follow
the instructions on-screen and in the Windows NT documentation to complete
the installation.
3
Microsoft Windows NT Installation