Hikvision DS-7316HQHI-SH User Manual - Page 118

Background, Foreground Recommended

Get Hikvision DS-7316HQHI-SH PDF manuals and user guides View all Hikvision DS-7316HQHI-SH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Figure 133 Create Array Interface 3. Edit the Array Name. 4. Select the RAID Level from RAID 0, RAID 1, RAID 5 and RAID 10. 5. Check the checkbox of corresponding disk to select the Physical Disk that you want to configure array. 6. Click OK to create array. 7. Click Array tab to view the successfully created array. 8. Click to select an array and click Create Vd to enter the Create Virtual Disk interface. Figure 134 Create Virtual Disk Interface 9. Edit the Virtual Disk Name. 10. Set the Capacity of the virtual disk. And at least 100 GB capacity must be configured for each virtual disk. You can click the Information of Array Capacity area to set the remaining capacity of the array for the disk. 11. Select the Initialization Type from Background, Foreground and Fast.  Background: The background initialization can synchronize the disks, and detect and repair the bad sector of the disks. During the background initialization, the virtual disk is allowed to be used.  Foreground (Recommended): By using foreground initialization, the RAID will be initialized totally and the bad sector of the hard disks can be detected and repaired. The virtual disk can be used only after the initialization is complete. 117

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
117
Figure 133
Create Array Interface
3.
Edit the Array Name.
4.
Select the RAID Level from RAID 0, RAID 1, RAID 5 and RAID 10.
5.
Check the checkbox of corresponding disk to select the Physical Disk that you want to
configure array.
6.
Click OK to create array.
7.
Click Array tab to view the successfully created array.
8.
Click to select an array and click Create Vd to enter the Create Virtual Disk interface.
Figure 134
Create Virtual Disk Interface
9.
Edit the Virtual Disk Name.
10.
Set the Capacity of the virtual disk. And at least 100 GB capacity must be configured for
each virtual disk. You can click the Information of Array Capacity area to set the
remaining capacity of the array for the disk.
11.
Select the Initialization Type from Background, Foreground and Fast.
Background:
The background initialization can synchronize the disks, and detect
and repair the bad sector of the disks. During the background initialization, the
virtual disk is allowed to be used.
Foreground (Recommended):
By using foreground initialization, the RAID will be
initialized totally and the bad sector of the hard disks can be detected and repaired.
The virtual disk can be used only after the initialization is complete.