IBM 17231RX Installation Guide - Page 16

Installing, keyboard, console

Get IBM 17231RX - 1U Flat-Panel Monitor Console PDF manuals and user guides
UPC - 000435862730
View all IBM 17231RX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Installing the keyboard in the console unit To install the keyboard in the console unit, complete the following steps: 1. Place the console unit on a table or other flat surface and make sure that the right side of the unit extends approximately 76 mm (3 in.) over the edge of the surface. This will help you route the keyboard-and-mouse cable more easily later in the procedure. (See the illustration in step 5 on page 7.) 2. Carefully lift the flat-panel display to the full upright position. Thumbscrews 3. If the keyboard that you are installing comes with two rubber pads on the underside of the keyboard, remove and discard them. (The rubber pads have an adhesive backing and can be peeled from the surface.) If you leave the rubber pads on the keyboard, they will extend into the 1U space below. Remove rubber pads (two places) Keyboard foot Attention: Do not extend the keyboard feet. The flat-panel display screen might be damaged if the feet are extended when the display is closed. 4. Peel the protective strip from the hook-and-loop fastener strip that comes with the console kit and attach it to the underside of the keyboard toward the front. Hook-and-loop fastener 6 1U 17-inch Flat Panel Console Kit: Installation and Maintenance Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Installing
the
keyboard
in
the
console
unit
To
install
the
keyboard
in
the
console
unit,
complete
the
following
steps:
1.
Place
the
console
unit
on
a
table
or
other
flat
surface
and
make
sure
that
the
right
side
of
the
unit
extends
approximately
76
mm
(3
in.)
over
the
edge
of
the
surface.
This
will
help
you
route
the
keyboard-and-mouse
cable
more
easily
later
in
the
procedure.
(See
the
illustration
in
step
5
on
page
7.)
2.
Carefully
lift
the
flat-panel
display
to
the
full
upright
position.
Thumbscrews
3.
If
the
keyboard
that
you
are
installing
comes
with
two
rubber
pads
on
the
underside
of
the
keyboard,
remove
and
discard
them.
(The
rubber
pads
have
an
adhesive
backing
and
can
be
peeled
from
the
surface.)
If
you
leave
the
rubber
pads
on
the
keyboard,
they
will
extend
into
the
1U
space
below.
Remove rubber pads
(two places)
Keyboard foot
Attention:
Do
not
extend
the
keyboard
feet.
The
flat-panel
display
screen
might
be
damaged
if
the
feet
are
extended
when
the
display
is
closed.
4.
Peel
the
protective
strip
from
the
hook-and-loop
fastener
strip
that
comes
with
the
console
kit
and
attach
it
to
the
underside
of
the
keyboard
toward
the
front.
Hook-and-loop fastener
6
1U
17-inch
Flat
Panel
Console
Kit:
Installation
and
Maintenance
Guide