IBM 6400-I15 User Manual - Page 128

to con any further settings on the print server

Get IBM 6400-I15 PDF manuals and user guides View all IBM 6400-I15 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 128 highlights

set sysinfo descramblekey 1234 Set the key value used for descrambling print jobs that have passed through IBM npscramble utility on a TCP/IP host. This key is a four-digit hexadecimal value obtained from the host software, npscramble. Within the npscramble source code, there is a variable called SR_KEY which contains the default key value. This can be changed to any four-digit value you would like. set sysinfo module [[-]novell] [[-]netbios] set sysinfo module -novell Enable and disable certain network protocol stacks within the Ethernet Interface. Sometimes it helps to disable any protocols you are not using on your network. set time hours [minutes [seconds]] set time 10 30 Set the current time noting the hours based on the 24-hour system and the minutes and seconds ranging from 0 to 59. If the Ethernet Interface is reset, this value will be lost so you will need to set the time again. set user add|del username IMPORTANT ! Be careful not to delete the root user, or you will be unable to configure any further settings on the print server. You will have to go back to factory defaults to correct this problem. set user add eng Add or remove a user on the Ethernet Interface defined by username. set user passwd username password set user passwd eng mplex1 Assign a password to a defined user on the Ethernet Interface. This password must be less than eleven characters. 7-16 Commands

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
7–16
Commands
set sysinfo descramblekey 1234
Set the key value used for descrambling print jobs that have passed through IBM
npscramble
utility on a TCP/IP host. This key is a four-digit hexadecimal value
obtained from the host software, npscramble. Within the npscramble source
code, there is a variable called SR_KEY which contains the default key value.
This can be changed to any four-digit value you would like.
set
sysinfo module [[–]novell] [[–]netbios]
set sysinfo module –novell
Enable and disable certain network protocol stacks within the Ethernet Interface.
Sometimes it helps to disable any protocols you are not using on your network.
set
time
hours
[
minutes
[
seconds
]]
set time 10 30
Set the current time noting the
hours
based on the 24-hour system and the
minutes
and
seconds
ranging from 0 to 59. If the Ethernet Interface is reset, this
value will be lost so you will need to set the time again.
set
user add|del
username
IMPORTANT
!
Be careful not to delete the root user, or you will be unable
to configure any further settings on the print server
. Y
ou
will have to go back to factory defaults to correct this
problem
.
set
user add eng
Add or remove a user on the Ethernet Interface defined by
username
.
set
user passwd
username password
set user passwd eng mplex1
Assign a
password
to a defined user on the Ethernet Interface. This
password
must be less than eleven characters.