IBM 6400-I15 User Manual - Page 130

and logpaths.

Get IBM 6400-I15 PDF manuals and user guides View all IBM 6400-I15 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 130 highlights

list Commands These commands list the current or working settings for a particular section within the command shell. To view stored settings in flash memory, you will need to add in "stored" within the beginning of any of the following commands. For example, "list prn" shows you the current prn settings but "list stored prn" shows you the settings sitting in flash memory. Normally these should match. list tcpip List all current TCP/IP network settings (e.g. IP address and subnet mask). list pserver List the current general print server settings (e.g. print server name and Novell mode). list dest List the current destination settings (e.g. names and mapped I/O ports, models, and logpaths). list model List the current model settings (e.g. names and mapped destinations). list logpath List the current logpath settings (e.g. names and mapped destinations). list prn List the current parallel port setting (e.g. mode). list sysinfo List the current Ethernet Interface system information (e.g. contact name and protocol stacks enabled). 7-18 Commands

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
7–18
Commands
list Commands
These commands list the current or working settings for a particular section
within the command shell. To view stored settings in flash memory, you will need
to add in “
stored
”
within the beginning of any of the following commands. For
example, “
list
prn
” shows you the current prn settings but “
list
stored prn
”
shows you the settings sitting in flash memory. Normally these should match.
list
tcpip
List all current TCP/IP network settings (e.g. IP address and subnet mask).
list
pserver
List the current general print server settings (e.g. print server name and Novell
mode).
list
dest
List the current destination settings (e.g. names and mapped I/O ports, models,
and logpaths).
list
model
List the current model settings (e.g. names and mapped destinations).
list
logpath
List the current logpath settings (e.g. names and mapped destinations).
list
prn
List the current parallel port setting (e.g. mode).
list
sysinfo
List the current Ethernet Interface system information (e.g. contact name and
protocol stacks enabled).