IBM 6400-I15 User Manual - Page 61

Example for Microsoft IP stacks

Get IBM 6400-I15 PDF manuals and user guides View all IBM 6400-I15 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

3. Use the "arp" command to add an entry into the Windows station ARP table for the Ethernet Interface. This is the most common syntax for this command: Syntax: arp -s ipaddress ethernetaddress Example for Microsoft IP stacks: arp -s 192.75.11.9 00-80-72-07-00-60 This example specifies a Ethernet Interface using IP address 192.75.11.9 and ethernet address 00:80:72:07:00:60. 4. Check to see if the ARP entry was accepted. arp -a You should see an entry in the listed ARP table with the IP address and ethernet address specified in Step 3. 5. Try to "ping" this IP address to see if the Ethernet Interface can be seen on your network. At this point, you should be able to communicate with the Ethernet Interface from your local Windows station. This means the print server knows about an IP address and subnet mask and has these settings in its current memory. However, if the Ethernet Interface is power cycled, these settings will disappear unless you store them into flash memory. To do this: 1. Load a Web browser on your Windows station and direct it to the URL "http://Ethernet InterfaceIPaddress/networkConf.html" (e.g. "http://192.75.11.9/networkConf.html"). NOTE: If prompted for a "User ID" and password first, type "root" for the ID and press ENTER at the password prompt since there is no password by default. 2. At the "Network Configuration" HTML form that displays, click in the field below the "IP Address" heading and type in the IP address for the Ethernet Interface. 3. Under the "Subnet Mask" heading, enter the Ethernet Interface subnet mask. Windows Configuration 4-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
4–5
Windows Configuration
3.
Use the “
arp
” command to add an entry into the Windows station ARP table
for the Ethernet Interface. This is the most common syntax for this command:
Syntax:
arp
–s
ipaddress ethernetaddress
Example for Microsoft IP stacks:
arp
–s 192.75.11.9 00–80–72–07–00–60
This example specifies a Ethernet Interface using IP address
192.75.11.9
and
ethernet address
00:80:72:07:00:60
.
4.
Check to see if the ARP entry was accepted.
arp
–a
You should see an entry in the listed ARP table with the IP address and ethernet
address specified in Step 3.
5.
Try to “
ping
” this IP address to see if the Ethernet Interface can be seen on
your network.
At this point, you should be able to communicate with the Ethernet Interface from
your local Windows station. This means the print server knows about an IP
address and subnet mask and has these settings in its current memory. However,
if the Ethernet Interface is power cycled, these settings will disappear unless you
store them into flash memory. To do this:
1.
Load a Web browser on your Windows station and direct it to the URL
“
http://
Ethernet
InterfaceIPaddress
/networkConf.html
”
(e.g. “
”).
NOTE:
If prompted for a “User ID” and password first, type “
root
” for the
ID and press ENTER at the password prompt since there is no
password by default.
2.
At the “Network Configuration” HTML form that displays, click in the field
below the “IP Address” heading and type in the IP address for the Ethernet
Interface.
3.
Under the “Subnet Mask” heading, enter the Ethernet Interface subnet mask.