IBM 6400-I15 User Manual - Page 133

List ROM contents.

Get IBM 6400-I15 PDF manuals and user guides View all IBM 6400-I15 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 133 highlights

debug eeprom List ROM contents. debug nif List network interface statistics. Miscellaneous Commands These commands do not fall under any specific section of the command shell but they are used quite frequently. save [default] Save the current settings to flash memory so they are available after power cycles. Sysinfo, destination, model, logpath, variable, user, and I/O port settings will be saved. If default is specified as well, factory settings will be saved, overwriting any new settings you have configured. reset Perform a warm boot or hardware reset simulating a power-on reset. Restores current settings to those stored in flash memory since the flash memory settings will be read and loaded into memory upon bootup. load [default] Load the settings stored in flash memory and use them as the current or working settings. If default is specified as well, factory settings will be loaded. lpstat [ioport] [jobID] lpstat prn Display active and queued jobs and I/O port status for a given ioport or jobID. Specifying one of these parameters will shorten the output focusing on the particular I/O port or print job specified. Commands 7-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
7–21
Commands
debug
eeprom
List ROM contents.
debug
nif
List network interface statistics.
Miscellaneous Commands
These commands do not fall under any specific section of the command shell but
they are used quite frequently.
save
[default]
Save the current settings to flash memory so they are available after power
cycles. Sysinfo, destination, model, logpath, variable, user, and I/O port settings
will be saved. If
default
is specified as well, factory settings will be saved,
overwriting any new settings you have configured.
reset
Perform a warm boot or hardware reset simulating a power-on reset. Restores
current settings to those stored in flash memory since the flash memory settings
will be read and loaded into memory upon bootup.
load
[default]
Load the settings stored in flash memory and use them as the current or working
settings. If
default
is specified as well, factory settings will be loaded.
lpstat
[
ioport
] [
jobID
]
lpstat prn
Display active and queued jobs and I/O port status for a given
ioport
or
jobID
.
Specifying one of these parameters will shorten the output focusing on the
particular I/O port or print job specified.