IBM 847661U Hardware Maintenance Manual - Page 96

External SCSI devices, The external SCSI

Get IBM 847661U - Netfinity 3000 - 61U PDF manuals and user guides View all IBM 847661U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

External SCSI devices Note If an internal device(s) is/are attached to the SCSI controller, only one external device is supported. The internal SCSI connector provides support for SCSI devices installed inside the server. The external SCSI connector provides support for external SCSI devices. The UltraSCSI adapter can support a maximum of 15 devices. Notes If you plan to install both internal and external SCSI devices, you must follow the instructions given in "Internal drives" on page 97 in addition to the instructions in this section. Read "Internal drives"; then, return here. For additional information about SCSI configurations supported, see http://www.ibm.com/pc/us/netfinity/ The server comes with a wide (16-bit) SCSI cable that supports 16-bit devices. If you want to attach narrow (8-bit) devices to the server, you must purchase a SCSI 68-pin to 50-Pin Converter that will enable the connection of the device to the cable that comes with the server. It is good practice not to exceed the following cable-length guidelines: - If you connect one or more UltraSCSI devices to the UltraSCSI adapter, do not exceed 1.5 meters (5 feet) total length for all cables (internal and external). - If you connect only Fast SCSI devices to the UltraSCSI adapter, do not exceed 3 meters (10 feet) total length for all cables (internal and external). Attention In addition to cable length and the number of installed devices, you must consider other factors that limit the performance of the SCSI subsystem. For example, if you install UltraSCSI devices in an external expansion enclosure that is limited to Fast transfer rates, or if you exceed the previously described cable-length guidelines, the transfer rate to all SCSI devices must be limited to Fast or standard transfer rates. You accomplish this by using the SCSISelect Utility program. See "SCSISelect utility program" on page 49 for additional information. If you plan to attach an external SCSI device, you must order an additional SCSI cable. That is, to use an external 88 Netfinity Server HMM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
External SCSI devices
Note
If an internal device(s) is/are attached to the SCSI
controller, only one external device is supported.
The internal SCSI connector provides support for SCSI
devices installed inside the server.
The external SCSI
connector provides support for external SCSI devices.
The
UltraSCSI adapter can support a maximum of 15 devices.
Notes
±
If you plan to install both internal and external
SCSI devices, you must follow the instructions
given in “Internal drives” on page
97 in addition
to the instructions in this section.
Read “Internal
drives”; then, return here.
For additional information about SCSI
configurations supported, see
±
The server comes with a wide (16-bit) SCSI
cable that supports 16-bit devices.
If you want to
attach narrow (8-bit) devices to the server, you
must purchase a SCSI 68-pin to 50-Pin
Converter that will enable the connection of the
device to the cable that comes with the server.
±
It is good practice not to exceed the following
cable-length guidelines:
–
If you connect one or more UltraSCSI
devices to the UltraSCSI adapter, do not
exceed 1.5 meters (5 feet) total length for all
cables (internal and external).
–
If you connect only Fast SCSI devices to the
UltraSCSI adapter, do not exceed 3 meters
(10 feet) total length for all cables (internal
and external).
Attention
In addition to cable length and the number of installed
devices, you must consider other factors that limit the
performance of the SCSI subsystem.
For example, if
you install UltraSCSI devices in an external expansion
enclosure that is limited to Fast transfer rates, or if you
exceed the previously described cable-length
guidelines, the transfer rate to all SCSI devices must
be limited to Fast or standard transfer rates.
You
accomplish this by using the SCSISelect Utility
program.
See “SCSISelect utility program” on
page
49 for additional information.
If you plan to attach an external SCSI device, you must
order an additional SCSI cable.
That is, to use an external
88
Netfinity Server HMM