IBM 847671U Hardware Maintenance Manual - Page 148

Continue rotating the latch handle counterclockwise, edge connector.

Get IBM 847671U - Netfinity 3000 - 71U PDF manuals and user guides
UPC - 087944520719
View all IBM 847671U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 148 highlights

6. Grasp and turn the latch clockwise to the extended position. This releases the system board from the riser card. Note Do not pull on the microprocessor, the DIMMs, or the DIMM sockets to remove the system board. Latch System Board Rail Tab Lift Here System Board Pull Here 7. Using the tab, slide the system board out and set it aside. To reinstall the system board: 1. Make sure that the system board latch handle is in the extended position. 2. Align the system board rails with the tracks on the chassis and slide the board in until it is approximately 6 mm (0.25 in) from the riser-card edge connector. 3. Rotate the latch handle counterclockwise until the the system board is properly aligned with the riser-card edge connector. 4. Continue rotating the latch handle counterclockwise while firmly pushing on the system board rail on the right-hand side of the system board. Note Do not push on the microprocessor, the DIMMs, or the DIMM sockets to install the system board. Make sure that the system board is fully seated in the riser-card edge connector. 140 Netfinity Server HMM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
6.
Grasp and turn the latch clockwise to the extended
position.
This releases the system board from the
riser card.
Note
Do not pull on the microprocessor, the DIMMs, or
the DIMM sockets to remove the system board.
System Board
Rail
Tab
Latch
Lift
Here
Pull
Here
System Board
7.
Using the tab, slide the system board out and set it
aside.
To reinstall the system board:
1.
Make sure that the system board latch handle is in
the extended position.
2.
Align the system board rails with the tracks on the
chassis and slide the board in until it is approximately
6 mm (0.25 in) from the riser-card edge connector.
3.
Rotate the latch handle counterclockwise until the the
system board is properly aligned with the riser-card
edge connector.
4.
Continue rotating the latch handle counterclockwise
while firmly pushing on the system board rail on the
right-hand side of the system board.
Note
Do not push on the microprocessor, the DIMMs,
or the DIMM sockets to install the system board.
Make sure that the system board is fully seated in the
riser-card edge connector.
140
Netfinity Server HMM