IBM 847671U Hardware Maintenance Manual - Page 51

See Installing or removing ISA and PCI, When the Configuration/Setup Utility program starts

Get IBM 847671U - Netfinity 3000 - 71U PDF manuals and user guides
UPC - 087944520719
View all IBM 847671U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Notes Using the Configuration/Setup Utility program, record all configuration information. Read "Safety information" on page 212. Power-off the server, but do not disconnect the cables. Remove the server cover. Place the server on its side. 1. Locate the Clear CMOS Request jumper (J9) on the system board (see "System board illustration" on page 142). You might have to remove adapters to gain access to the jumper. See "Installing or removing ISA and PCI adapters" on page 62. 2. Move the jumper from its normal position (pins 1 and 2) to pins 2 and 3. It might be helpful to use needlenose pliers to move the jumper, but be careful not to scrape any system board components or to crush the jumper. 21 3 1 2 3 21 3 3. Power-on the server back on for approximately 10 seconds. 4. Power-off the server. 5. Power-on the server back on. 6. CMOS memory is now cleared and the passwords have been erased. After the POST completes, configuration error messages are displayed. Note You might not be able to power-off the power using the power switch until POST is nearly complete. Unplug the power cord to power-off the server. 7. Follow the instructions on the screen to continue. 8. When the Configuration/Setup Utility program starts, make the necessary changes, save the settings, and exit setup. You must update the server configuration. When you see a message that instructs you to move the jumper to the normal position, Power-off the server. IBM Netfinity 3000 - Type 8476 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
Notes
±
Using the Configuration/Setup Utility program,
record all configuration information.
±
Read “Safety information” on page
212.
±
Power-off the server, but do not disconnect the
cables.
±
Remove the server cover.
±
Place the server on its side.
1.
Locate the
Clear CMOS Request
jumper
(J9) on the
system board (see “System board illustration” on
page 142).
You might have to remove adapters to gain access to
the jumper.
See “Installing or removing ISA and PCI
adapters” on page
62.
2.
Move the jumper from its normal position (pins 1 and
2) to pins 2 and 3.
It might be helpful to use
needlenose pliers to move the jumper, but be careful
not to scrape any system board components or to
crush the jumper.
1
2
3
1
2
3
1
2
3
3.
Power-on the server back on for approximately 10
seconds.
4.
Power-off the server.
5.
Power-on the server back on.
6.
CMOS memory is now cleared and the passwords
have been erased.
After the POST completes,
configuration error messages are displayed.
Note
You might not be able to power-off the power
using the power switch until POST is nearly
complete.
Unplug the power cord to power-off
the server.
7.
Follow the instructions on the screen to continue.
8.
When the Configuration/Setup Utility program starts,
make the necessary changes, save the settings, and
exit setup.
You must update the server configuration.
When you see a message that instructs you to move
the jumper to the normal position, Power-off the
server.
IBM Netfinity 3000 - Type 8476
43