IBM 8685 Hardware Maintenance Manual - Page 29

Using the SCSISelect utility program, Choices available from the SCSISelect menu

Get IBM 8685 - eServer xSeries 255 PDF manuals and user guides
UPC - 087944957171
View all IBM 8685 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Using the SCSISelect utility program SCSISelect is a built-in, menu-driven configuration utility program that you can use to: v View the default SCSI IDs v Locate and correct configuration conflicts v Perform a low-level format on a SCSI hard disk (some servers) The following sections provide the instructions to start the SCSISelect Utility and descriptions of the available menu choices. Note: If your server has a RAID adapter installed, use the configuration method supplied with the RAID adapter to view or change SCSI settings for attached devices. Starting the SCSISelect utility program Complete the following steps to start the SCSISelect utility program: 1. Turn on the server. 2. When the > prompt appears, press Ctrl+A. Note: If an administrator password has been set, you are prompted to type the password to start the SCSISelect Utility program. 3. When prompted, select either channel A (external) or channel B (internal). 4. Use the arrow keys to select a choice from the menu. v Press Esc to return to the previous menu. v Press F5 to switch between color and monochrome modes (if your monitor permits). 5. Follow the instructions on the screen to change the settings of the selected items; then, press Enter. Choices available from the SCSISelect menu The following choices appear on the SCSISelect Utility menu: v Configure/View Host Adapter Settings Select this choice to view or change the SCSI controller settings. To reset the SCSI controller to its default values, press F6; then, follow the instructions that appear on the screen. You can view or change the following controller settings: - Host Adapter SCSI ID Select this choice to view the SCSI controller ID, which is usually 7. - SCSI Parity Checking The assigned value for this setting is Enabled, and it cannot be changed. - Host Adapter SCSI Termination The assigned value for this setting is Enabled, and it cannot be changed. - Boot Device Options Select this choice to configure startable device parameters. Before you can make updates, you must know the ID of the device whose parameters you want to configure. - SCSI Device Configuration Chapter 2. Configuration 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
Using the SCSISelect utility program
SCSISelect is a built-in, menu-driven configuration utility program that you can use
to:
v
View the default SCSI IDs
v
Locate and correct configuration conflicts
v
Perform a low-level format on a SCSI hard disk (some servers)
The following sections provide the instructions to start the SCSISelect Utility and
descriptions of the available menu choices.
Note:
If your server has a RAID adapter installed, use the configuration method
supplied with the RAID adapter to view or change SCSI settings for attached
devices.
Starting the SCSISelect utility program
Complete the following steps to start the SCSISelect utility program:
1.
Turn on the server.
2.
When the
<<< Press <CTRL><A> for SCSISelect Utility! >>>
prompt appears,
press Ctrl+A.
Note:
If an administrator password has been set, you are prompted to type the
password to start the SCSISelect Utility program.
3.
When prompted, select either channel A (external) or channel B (internal).
4.
Use the arrow keys to select a choice from the menu.
v
Press Esc to return to the previous menu.
v
Press F5 to switch between color and monochrome modes (if your monitor
permits).
5.
Follow the instructions on the screen to change the settings of the selected
items; then, press Enter.
Choices available from the SCSISelect menu
The following choices appear on the SCSISelect Utility menu:
v
Configure/View Host Adapter Settings
Select this choice to view or change the SCSI controller settings. To reset the
SCSI controller to its default values, press F6; then, follow the instructions that
appear on the screen.
You can view or change the following controller settings:
–
Host Adapter SCSI ID
Select this choice to view the SCSI controller ID, which is usually 7.
–
SCSI Parity Checking
The assigned value for this setting is
Enabled
, and it cannot be changed.
–
Host Adapter SCSI Termination
The assigned value for this setting is
Enabled
, and it cannot be changed.
–
Boot Device Options
Select this choice to configure startable device parameters. Before you can
make updates, you must know the ID of the device whose parameters you
want to configure.
–
SCSI Device Configuration
Chapter 2. Configuration
19