IBM 8685 Hardware Maintenance Manual - Page 82

connecting the unattached end of the cable to an internal channel connector

Get IBM 8685 - eServer xSeries 255 PDF manuals and user guides
UPC - 087944957171
View all IBM 8685 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

connecting the unattached end of the cable to an internal channel connector on the adapter (see "Cabling a RAID or SCSI adapter" on page 58). Attention: Do not block the ventilated space in front of the fan assembly. 27. Slide the hot-swap hard disk drives back into bays 1 through 6 to reconnect the drives to the standard SCSI backplane. 28. Install additional internal hot-swap hard disk drives in bays 7 through 12 to connect the drives to the optional 6-Pack hot-swap drive backplane (see "Installing a hot-swap hard disk drive" on page 75). Note: The optional 6-Pack hot-swap drive backplane sets the SCSI IDs for these hot-swap hard disk drives. See "Setting SCSI IDs" on page 113 for additional information. 29. If your server is a tower model, continue with the next step. If your server is a rack model and you have already installed the server in a rack enclosure, you must reconnect the cable-management-arm bracket to the server. a. Slide the server into the rack. b. Reattach the cable-management-arm bracket to the server. Cable-management arm bracket Cable-management arm Captive screw Tab Fan bay 7 (fan removed) 1) Remove the fan from fan bay 7. 2) Insert the tab on the cable-management-arm bracket into the corresponding slot on the server. 72 xSeries 255 Type 8685: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
connecting the unattached end of the cable to an internal channel connector
on the adapter (see “Cabling a RAID or SCSI adapter” on page 58).
Attention:
Do not block the ventilated space in front of the fan assembly.
27.
Slide the hot-swap hard disk drives back into bays 1 through 6 to reconnect
the drives to the standard SCSI backplane.
28.
Install additional internal hot-swap hard disk drives in bays 7 through 12 to
connect the drives to the optional 6-Pack hot-swap drive backplane (see
“Installing a hot-swap hard disk drive” on page 75).
Note:
The optional 6-Pack hot-swap drive backplane sets the SCSI IDs for
these hot-swap hard disk drives. See “Setting SCSI IDs” on page 113
for additional information.
29.
If your server is a tower model, continue with the next step.
If your server is a rack model and you have already installed the server in a
rack enclosure, you must reconnect the cable-management-arm bracket to the
server.
a.
Slide the server into the rack.
b.
Reattach the cable-management-arm bracket to the server.
Tab
Fan bay 7
(fan removed)
Captive
screw
Cable-management
arm
Cable-management
arm bracket
1)
Remove the fan from fan bay 7.
2)
Insert the tab on the cable-management-arm bracket into the
corresponding slot on the server.
72
xSeries 255 Type 8685: Hardware Maintenance Manual and Troubleshooting Guide