IBM 8862 Hardware Maintenance Manual - Page 82

Operator, information, panel

Get IBM 8862 - Eserver xSeries 365 PDF manuals and user guides
UPC - 000435172679
View all IBM 8862 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

b. Place the cable into the cable connector and pull the bottom edge of the connector toward the front of the server to secure the cable. 10. Attach the wire to the diskette drive beginning with the front hole, making sure to guide the wire into the hook. 11. Replace the bezel and top cover. 12. Reconnect external cables and power cords. Operator information panel This section contains information about removing and replacing the operator information panel. Note: v v v Read "Installation guidelines" on page 29. Read "Safety information" on page 147. Read "Handling static-sensitive devices" on page 30. Complete the following steps to replace the operator information panel assembly: 1. Turn off the server and all peripheral devices; then, disconnect all power cords and external cables. 2. Remove the top cover and bezel (see "Removing the cover and bezel" on page 32). 3. Remove the cable from the media interposer card. 4. Remove the screw securing the corner of the pivoting panel to the chassis. When the screw is fully loosened, it might be necessary to insert the blade of the screwdriver slightly under the head of the screw and lever it up. Curved channel Release latch 5. Press the blue latch on the front panel to release the assembly. Do not pivot the assembly. 6. Pull the assembly slightly out of the server without pivoting the assembly. 7. Pull the assembly out of the front of the server. It might be necessary to lift the assembly up slightly while sliding it out. 8. Assemble the replacement operator information panel and cable. 9. Guiding the cable through first, insert the assembly into the server through the front. The shoulder screw on the bottom of the assembly will glide along the straight guide channel in the chassis. 10. Gently slide the assembly into the server along the straight guide channel, keeping the cable free. When the assembly is inserted all the way, the 72 IBM xSeries 365 Types 8861, 8862: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
b.
Place
the
cable
into
the
cable
connector
and
pull
the
bottom
edge
of
the
connector
toward
the
front
of
the
server
to
secure
the
cable.
10.
Attach
the
wire
to
the
diskette
drive
beginning
with
the
front
hole,
making
sure
to
guide
the
wire
into
the
hook.
11.
Replace
the
bezel
and
top
cover.
12.
Reconnect
external
cables
and
power
cords.
Operator
information
panel
This
section
contains
information
about
removing
and
replacing
the
operator
information
panel.
Note:
v
Read
“Installation
guidelines”
on
page
29.
v
Read
“Safety
information”
on
page
147.
v
Read
“Handling
static-sensitive
devices”
on
page
30.
Complete
the
following
steps
to
replace
the
operator
information
panel
assembly:
1.
Turn
off
the
server
and
all
peripheral
devices;
then,
disconnect
all
power
cords
and
external
cables.
2.
Remove
the
top
cover
and
bezel
(see
“Removing
the
cover
and
bezel”
on
page
32).
3.
Remove
the
cable
from
the
media
interposer
card.
4.
Remove
the
screw
securing
the
corner
of
the
pivoting
panel
to
the
chassis.
When
the
screw
is
fully
loosened,
it
might
be
necessary
to
insert
the
blade
of
the
screwdriver
slightly
under
the
head
of
the
screw
and
lever
it
up.
Release latch
Curved channel
5.
Press
the
blue
latch
on
the
front
panel
to
release
the
assembly.
Do
not
pivot
the
assembly.
6.
Pull
the
assembly
slightly
out
of
the
server
without
pivoting
the
assembly.
7.
Pull
the
assembly
out
of
the
front
of
the
server.
It
might
be
necessary
to
lift
the
assembly
up
slightly
while
sliding
it
out.
8.
Assemble
the
replacement
operator
information
panel
and
cable.
9.
Guiding
the
cable
through
first,
insert
the
assembly
into
the
server
through
the
front.
The
shoulder
screw
on
the
bottom
of
the
assembly
will
glide
along
the
straight
guide
channel
in
the
chassis.
10.
Gently
slide
the
assembly
into
the
server
along
the
straight
guide
channel,
keeping
the
cable
free.
When
the
assembly
is
inserted
all
the
way,
the
72
IBM
xSeries
365
Types
8861,
8862:
Hardware
Maintenance
Manual
and
Troubleshooting
Guide