IBM 8862 Hardware Maintenance Manual - Page 83

Media, interposer

Get IBM 8862 - Eserver xSeries 365 PDF manuals and user guides
UPC - 000435172679
View all IBM 8862 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

shoulder screw on the bottom of the assembly will slide into and along the curved channel. This allows the panel to swing out. 11. Reinstall the screw that was removed in step 4 on page 72. 12. Verify that the assembly opens and closes smoothly. 13. Close and latch the operator information panel. 14. Connect the cable to the media interposer card. 15. Replace the bezel and top cover. 16. Reconnect external cables and power cords. Media interposer card This section contains information about removing and replacing the media interposer card. Note: v v v Read "Installation guidelines" on page 29. Read "Safety information" on page 147. Read "Handling static-sensitive devices" on page 30. Complete the following steps to remove the media interposer card: 1. Turn off the server and all peripheral devices; then, disconnect all power cords and external cables. 2. Remove the top cover (see "Removing the cover and bezel" on page 32). 3. Pull the CD-ROM drive or DVD-ROM drive out of the server slightly to disengage it from the media interposer card. 4. Disconnect all cables from the media interposer card. Pushpins 5. Pull out the two blue push pins. Chapter 5. FRU information (service only) 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
shoulder
screw
on
the
bottom
of
the
assembly
will
slide
into
and
along
the
curved
channel.
This
allows
the
panel
to
swing
out.
11.
Reinstall
the
screw
that
was
removed
in
step
4
on
page
72.
12.
Verify
that
the
assembly
opens
and
closes
smoothly.
13.
Close
and
latch
the
operator
information
panel.
14.
Connect
the
cable
to
the
media
interposer
card.
15.
Replace
the
bezel
and
top
cover.
16.
Reconnect
external
cables
and
power
cords.
Media
interposer
card
This
section
contains
information
about
removing
and
replacing
the
media
interposer
card.
Note:
v
Read
“Installation
guidelines”
on
page
29.
v
Read
“Safety
information”
on
page
147.
v
Read
“Handling
static-sensitive
devices”
on
page
30.
Complete
the
following
steps
to
remove
the
media
interposer
card:
1.
Turn
off
the
server
and
all
peripheral
devices;
then,
disconnect
all
power
cords
and
external
cables.
2.
Remove
the
top
cover
(see
“Removing
the
cover
and
bezel”
on
page
32).
3.
Pull
the
CD-ROM
drive
or
DVD-ROM
drive
out
of
the
server
slightly
to
disengage
it
from
the
media
interposer
card.
4.
Disconnect
all
cables
from
the
media
interposer
card.
Pushpins
5.
Pull
out
the
two
blue
push
pins.
Chapter
5.
FRU
information
(service
only)
73