IBM SAN16B-2 User Guide - Page 34

Attention

Get IBM SAN16B-2 - TotalStorage Express Model Switch PDF manuals and user guides
UPC - 000435819895
View all IBM SAN16B-2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

2. Separate the inner and outer slides. a. Open one of the slides until the lock engages. b. Press the lock release lever ( 1 in Figure 4) and remove the inner rail from the outer rail. 1 Figure 4. Separating the inner and outer rails. c. Repeat step 2a and step 2b for the other rail. SJ000046 Note: For racks with flush-mount doors, such as the 9306 Netfinity racks, do not install the ears. Instead, use the rack-mount slides by attaching the switch to the set of mounting holes, which are offset 3 inches into the rack. 3. Install the inner (smaller) slide on the switch chassis, as Figure 3 on page 11 shows. Attention: If you use screws longer than 3/16 in., you can damage the switch. a. Position the flat side of the inner rail along one side of the switch. Align the holes in the rail with the threaded holes in the side of the switch chassis. The chamfered end of the inner rail should face toward the rear of the switch (away from the ports) as shown in Figure 5 on page 13. b. Attach the inner rail by using three of the 8-32 x 3/16 in. zinc screws ( 6 in Table 4 on page 11). 12 SAN16B-2 Installation, Service, and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
2.
Separate
the
inner
and
outer
slides.
a.
Open
one
of
the
slides
until
the
lock
engages.
b.
Press
the
lock
release
lever
(
±1²
in
Figure
4)
and
remove
the
inner
rail
from
the
outer
rail.
c.
Repeat
step
2a
and
step
2b
for
the
other
rail.
Note:
For
racks
with
flush-mount
doors,
such
as
the
9306
Netfinity
racks,
do
not
install
the
ears.
Instead,
use
the
rack-mount
slides
by
attaching
the
switch
to
the
set
of
mounting
holes,
which
are
offset
3
inches
into
the
rack.
3.
Install
the
inner
(smaller)
slide
on
the
switch
chassis,
as
Figure
3
on
page
11
shows.
Attention:
If
you
use
screws
longer
than
3/16
in.,
you
can
damage
the
switch.
a.
Position
the
flat
side
of
the
inner
rail
along
one
side
of
the
switch.
Align
the
holes
in
the
rail
with
the
threaded
holes
in
the
side
of
the
switch
chassis.
The
chamfered
end
of
the
inner
rail
should
face
toward
the
rear
of
the
switch
(away
from
the
ports)
as
shown
in
Figure
5
on
page
13.
b.
Attach
the
inner
rail
by
using
three
of
the
8-32
x
3/16
in.
zinc
screws
(
±6²
in
Table
4
on
page
11).
SJ000046
1
Figure
4.
Separating
the
inner
and
outer
rails.
12
SAN16B-2
Installation,
Service,
and
User’s
Guide