IBM SAN16B-2 User Guide - Page 37

SAN16B-2

Get IBM SAN16B-2 - TotalStorage Express Model Switch PDF manuals and user guides
UPC - 000435819895
View all IBM SAN16B-2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Figure 7. Inserting slides into the rack rails SJ000049 b. Check the alignment of the slides by sliding the switch in and out of the rack. Any difficulty moving the switch indicates lateral stress or misalignment. If this situation occurs, adjust the slide positions until the movement is smooth. 8. Optional step: If the right and left rack mount brackets are installed on the front corners of the switch, attach both brackets to the cabinet rack by using M5 x 12 screws 7 . See step 4 on page 13 and Figure 3 on page 11. The screws should pass through the front of each bracket and the slide rail. Note: Some rack mount kits might use 10-32 nut clips in place of the M5 nut clips for the locking ears. 9. Continue with initial setup of the switch by following the procedures in "Cabling and configuring the SAN16B-2" on page 16. DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the devices that attach to the system. It is the responsibility of the customer to ensure that the outlet is correctly wired and grounded to prevent an electrical shock. (D004) Note: Do not connect the switch to the network until you perform one of the following steps: v Set the internet protocol (IP) address. v Verify that the default IP address does not conflict with the existing IP addresses in the same network. Chapter 2. Installing and configuring the SAN16B-2 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
b.
Check
the
alignment
of
the
slides
by
sliding
the
switch
in
and
out
of
the
rack.
Any
difficulty
moving
the
switch
indicates
lateral
stress
or
misalignment.
If
this
situation
occurs,
adjust
the
slide
positions
until
the
movement
is
smooth.
8.
Optional
step:
If
the
right
and
left
rack
mount
brackets
are
installed
on
the
front
corners
of
the
switch,
attach
both
brackets
to
the
cabinet
rack
by
using
M5
x
12
screws
±7²
.
See
step
4
on
page
13
and
Figure
3
on
page
11.
The
screws
should
pass
through
the
front
of
each
bracket
and
the
slide
rail.
Note:
Some
rack
mount
kits
might
use
10-32
nut
clips
in
place
of
the
M5
nut
clips
for
the
locking
ears.
9.
Continue
with
initial
setup
of
the
switch
by
following
the
procedures
in
“Cabling
and
configuring
the
SAN16B-2”
on
page
16.
DANGER
An
electrical
outlet
that
is
not
correctly
wired
could
place
hazardous
voltage
on
metal
parts
of
the
system
or
the
devices
that
attach
to
the
system.
It
is
the
responsibility
of
the
customer
to
ensure
that
the
outlet
is
correctly
wired
and
grounded
to
prevent
an
electrical
shock.
(D004)
Note:
Do
not
connect
the
switch
to
the
network
until
you
perform
one
of
the
following
steps:
v
Set
the
internet
protocol
(IP)
address.
v
Verify
that
the
default
IP
address
does
not
conflict
with
the
existing
IP
addresses
in
the
same
network.
SJ000049
Figure
7.
Inserting
slides
into
the
rack
rails
Chapter
2.
Installing
and
configuring
the
SAN16B-2
15