Icom IC-7000 Instruction Manual - Page 18

1 PANEL DESCRIPTION ■ Microphone (HM-151) z SPCH/LOCK KEY [SPCH/LOCK] ➥ Push momentarily to have the frequency, etc. announced by the speech synthesizer. (p. 34) • The parameters to be announced can be selected in the miscellaneous (others) Set mode. (p. 132) ➥ Hold down for 1 second to toggle the microphone lock function ON or OFF. (p. 37) x PTT SWITCH [PTT] (p. 37) Hold down to transmit; release to receive. c UP/DOWN SWITCHES [Y]/[Z] Change the operating frequency. • Hold down to change the frequency repeatedly. • Tuning step size is 50 Hz if no TS indicator is displayed. v TRANSMIT INDICATOR (p. 37) Lights red while transmitting. b KEYPAD ➥ Pushing a key selects the operating band. • [(GENE)•] selects the general coverage band. ➥ Pushing the same key 2 or 3 times calls up other stacked frequencies in the band. (p. 28) • Icom's triple band stacking register memorizes 3 frequencies in each band. ➥ After pushing [(F-INP)ENT], enter a numeric frequency, followed by pressing [(F-INP)ENT] again. (p. 29) • e.g. to enter 14.195 MHz, push [(F-INP)ENT] [1] [4] [•] [1] [9] [5] [(F-INP)ENT]. n FILTER SELECTION [FIL] ➥ Push momentarily to select one of three IF filter settings. (p. 75) ➥ H old down for 1 second to enter the filter Set mode. (p. 76) m MODE KEY [MODE] (p. 34) ➥ Push momentarily to cycle through the operating modes: USB/LSB ➧ CW/CW-R ➧ RTTY/RTTY-R ➧ AM/FM/WFM ➥ Hold down for 1 second to toggle the following operating modes: USB ↔ LSB CW ↔ CW-R RTTY ↔ RTTY-R AM → FM → WFM → AM, etc , POWER INDICATOR Lights green while transceiver power is ON. See the illustration of the HM-151 on page i-2. . PROGRAMMABLE FUNCTION KEYS [F-1]/[F-2] Program and perform a selected function. • The functions can be assigned in the miscellaneous (others) Set mode (p. 133). The default settings for [F-1] and [F-2] are "MPW" and "MPR," respectively. Default settings [F-1] (MPW): Push to store the selected readout frequency and operating mode into a memo pad. [F-2] (MPR): Push to call up a memo pad. ⁄0 MEMORY WRITE [MW] (pp. 101, 102) Hold down for 1 second to store the displayed VFO frequency and operating mode into the displayed memory channel. ⁄1 VFO/MEMORY SELECTION [V/M] ➥ P ush momentarily to toggle VFO and memory modes. (pp. 27, 100) ➥ H old down for 1 second to transfer the selected memory channel to the currently displayed VFO. (p. 107) ⁄2 TRANSMIT FREQUENCY CHECK [XFC] (pp. 65, 89) Monitors the transmit frequency when held down. • While holding down this key, the transmit frequency can be changed with [DIAL]. ⁄3 TUNER/CALL KEY [TUNER/CALL] ➥ During HF/50 MHz operation (p. 114): ● Push momentarily to toggle the automatic antenna tuner function ON or OFF. • An optional antenna tuner must be connected indicator appears when the tuner is ON. ● Hold down for 2 seconds to manually tune the antenna. • An optional antenna tuner must be connected indicator appears when the tuner is ON. ➥ During 144/430 MHz operation (p. 100): Push momentarily to select the call channel (or return to the previous channel/frequency when the call channel is already selected). • "C1" is the 144 MHz call channel and "C2" is the 430 MHz call channel. 9