Insignia NS-LBD32X-10A User Manual (English) - Page 57

Insignia 32" LCD TV/Blu-ray DVD Combo, 1080p Blu-ray Disc problems Problem Solution Remote control does not work • Make sure that you point the remote control at the remote control sensor on the front of your player. For more information, see "Aiming the remote control" on page 8. • Make sure that there is no obstruction between the remote control and the remote control sensor. • Make sure that bright light does not shine on the remote control sensor. Bright light can interfere with signal reception. • Make sure that colored glass is not in front of the remote control sensor. Colored glass can interfere with signal reception. • The batteries may be dead. Replace the batteries. TV/Blu-ray combo does not work • A built-in safety device may have been activated. Press POWER on the side of your TV/Blu-ray combo to turn it off, then turn it on again. If your TV/Blu-ray combo still does not turn on, unplug the power cord, wait about one minute, plug it in again, then press POWER on the side of your TV/Blu-ray combo. • Condensation may have formed inside your TV/Blu-ray combo. Turn off your TV/Blu-ray combo and wait about two to three hours for the condensation to evaporate. Playback will not start, or playback starts then stops • If you see , the action you are trying is not allowed by your TV/Blu-ray combo or the disc. • Make sure that the disc is inserted with the label facing forward. • Make sure that the disc is not dirty. To clean the disc, see "Cleaning discs" on page 52. • The disc may be blank or not compatible with your TV/Blu-ray combo. For a list of compatible discs, see "Playable discs" on page 36. Startup is slow • Startup may be slow if the TV is connected to the HDMI cable. • Startup may be slow the first time you plug in the power cord or after a power failure. Disc tray opens automatically while playing • Make sure that the disc is not dirty. To clean the disc, see "Cleaning discs" on page 52. • The disc may be blank or not compatible with your V/Blu-ray combo. For a list of compatible discs, see "Playable discs" on page 36. • Try resetting your player. Press POWER, wait five seconds, then press POWER again. The player is on and displays the start logo and menu, but there is no image from the disc displayed • Make sure that the disc is not dirty. To clean the disc, see "Cleaning discs" on page 52. • Try resetting your player. Press POWER, wait five seconds, then press POWER again. TV problems Problem Solution Ghosts in picture Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected by tall buildings, hills or other large objects. Try changing the direction or position of the antenna to improve the reception. Black spots or horizontal streaks may appear or the picture may flutter or drift because of interference from automobile ignition systems, neon lamps, or Picture has spots, streaks, or it AC-powered tools and appliances, such as drills or flutters hair dryers. Turn off appliances, plug the power cord into another power outlet, preferably on a different circuit, or move your TV/Blu-ray combo to another location. Picture has snow If the TV is located far from the TV station, such as in a fringe reception area where the signal is weak, small dots may appear in the picture. If the signal is extremely weak, the installation of a larger external antenna may be necessary. Radio frequency interference (RFI) RFI can be caused by two-way radios. This type of interference produces moving ripples or diagonal streaks in the picture. Some cases may cause a loss of contrast in the picture. Changing the direction and position of the antenna or installing an RFI filter may improve the picture. A slight picture size variation is normal when you Slight picture size variations adjust the contrast or brightness setting. Poor or no sound • The station or cable TV provider may be experiencing problems. Tune to another station. • Check volume adjustments or muting. • Check for sources of possible interference. Poor reception on some channels • The station or cable TV provider may be experiencing problems. Tune to another station. • Station signal is weak. Reorient the antenna to receive stronger reception. • Check for sources of possible interference. Poor color or no color • The station or cable TV provider may be experiencing problems. Tune to another station. • Make sure that you have scanned for channels. See "Automatically scanning for channels" on page 23. • Adjust the picture settings. See "Adjusting the picture settings" on page 17. • Check antenna or cable TV connections or reorient the antenna. • Check for sources of possible interference. Picture wobbles or drifts • The station or cable TV provider may be experiencing problems. Tune to another station. • Make sure that you have scanned for channels. See "Automatically scanning for channels" on page 23. • The cable TV provider is scrambling the channel. • Check the antenna orientation. No cable TV reception • Check all cable TV connections. • Set Signal Type to Cable. See "Selecting the TV signal source" on page 23. • The station or cable TV provider may be experiencing problems. Tune to another station. Horizontal or diagonal bars on the screen • Check antenna connections and try reorienting it. • Check for sources of possible interference. www.insigniaproducts.com 53