Insignia NS-R5101AHD-A User Manual (English) - Page 19
Speaker Matching Error
![]() |
UPC - 600603128851
View all Insignia NS-R5101AHD-A manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
NS-R5101AHD-A_10-0487_MAN_.book Page 15 Friday, May 7, 2010 7:51 AM Insignia NS-R5101AHD-A AV Home Theater Receiver Notes • • Make the room as quiet as possible. Background noise and Radio Frequency Interference (RFI) can disrupt the room measurements. Close windows, and turn off televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices. Silence the cell phone (even if it is not in use) or place it away from all audio electronics. The microphone picks up test tones which played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup run. To use Audyssey to set up and correct your speakers: Note • Room correction and speaker setup cannot be performed while a pair of headphones is connected. 1 Turn on the receiver and the connected TV. 2 On the TV, select the input to which the receiver is connected. 3 Set the speaker setup microphone at the Main Listening Position 1, and connect it to the SETUP MIC jack on the front of the receiver. SETUP MIC jack Speaker setup microphone The speaker setting menu appears. Note The on-screen setup menus only appear on a TV that is connected to the HDMI OUT jack. If your TV is connected to the MONITOR OUT V or COMPONENT VIDEO OUT jacks, use the receiver's display when changing the settings. 4 Press ENTER. The room correction and speaker setup starts. Test tones are played through each speaker as Audyssey 2EQ® Room Correction and Speaker Setup runs. This process takes a few minutes. Refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during the room correction and speaker setup unless you want to cancel the setup. 5 Place the setup microphone at the next position, then press ENTER. Audyssey 2EQ® performs more measurements. This takes a few minutes. 6 When prompted, place the setup microphone at the next position, then repeat step 5. 7 Use or to select an option, then press ENTER. The options are: • Save-To save the calculated settings and exit the room correction and speaker setup. • Cancel-To cancel the room correction and speaker setup. Note You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by using or . 8 Disconnect the speaker setup microphone. Notes • • • • • When Audyssey 2EQ® Room Correction and Speaker Setup is complete, Audyssey is set to On and the Audyssey indicator lights. You can cancel Audyssey 2EQ® Room Correction and Speaker Setup at any point in this procedure by disconnecting the setup microphone. Do not connect or disconnect any speakers during Audyssey 2EQ® Room Correction and Speaker Setup. If the receiver is muted, it will be unmuted automatically when Audyssey 2EQ® Room Correction and Speaker Setup starts. Changes to the room after Audyssey 2EQ® Room Correction and Speaker Setup requires that you run Audyssey 2EQ ® Room Correction and Speaker Setup again, as room EQ characteristics may have changed. Error Messages While the room correction and speaker setup is in progress, one of the following error messages may appear: • Retry-Try again. • Cancel-Cancel the room correction and speaker setup. • Ambient noise is too high-The background noise is too loud. Remove the source of the noise and try again. • Speaker Matching Error!-The number of speakers detected was different from that of the first measurement. Check the speaker connection. • Writing Error!-This message appears if saving fails. Try saving again. If this message appears after two or three attempts, contact your Insignia dealer. • Speaker Detect Error-This message appears if a speaker is not detected. No means that no speaker was detected. Changing the speaker settings manually You can manually make changes to the settings found during the room correction and speaker setup. See also: • "Configuring speakers (Sp Config menu)" on page 21. • "Setting speaker distance (Sp Distance menu)" on page 22. • "Setting the level calibration (Level Cal menu)" on page 22. Using the powered subwoofer The powered subwoofer outputs very low-frequency sound at a low volume level, therefore it may not be detected by Audyssey 2EQ® Room Correction and Speaker Setup. www.insigniaproducts.com 15
![](/manual_guide/products/insignia-nsr5101ahda-user-manual-english-5f0f961/19.png)