Insignia NS-R5101AHD-A User Manual (English) - Page 21
Listening to your receiver
UPC - 600603128851
View all Insignia NS-R5101AHD-A manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 21 highlights
NS-R5101AHD-A_10-0487_MAN_.book Page 17 Friday, May 7, 2010 7:51 AM Insignia NS-R5101AHD-A AV Home Theater Receiver The output is muted and the MUTING indicator flashes on the display. Tip • To unmute, press MUTING again or adjust the volume. • Muting is also cancelled when the receiver is set to Standby. Using the sleep timer With the sleep timer, you can set the receiver to turn off automatically after a specified period. To use the sleep timer: • Press RECEIVER, then press SLEEP repeatedly to select the sleep time you want. The sleep time can be set from 90 to 10 minutes, in 10 minute steps. The SLEEP indicator lights on the display when the sleep timer has been set. The specified sleep time appears on the display for about five seconds, then the previous display reappears. Tip • To cancel the sleep timer, press SLEEP repeatedly until the SLEEP indicator goes off. • To check the time remaining until the receiver turns off, press SLEEP. If you press SLEEP while the sleep time is being displayed, the sleep time is shortened by 10 minutes. Using headphones To use headphones: • Connect a pair of stereo headphones with a standard plug (1/4 inch or 6.3 mm) to the PHONES jack. Tip • Always turn down the volume before connecting your headphones. • While the headphones plug is inserted in the PHONES jack, the speakers are turned off. • When you connect a pair of headphones, the listening mode is set to Stereo, unless it is already set to Stereo, Mono, or Direct. • The listening modes cannot be selected while a pair of headphones is connected. Listening to your receiver Important: The procedures described in this section use the buttons on the front panel, unless otherwise specified. Listening to the radio With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. To listen to the radio: • Press TUNER to select either AM or FM (each time you press TUNER, the radio band changes between AM and FM). In this example, FM has been selected. Band Frequency • To automatically tune to a station: • Press TUNING MODE until the AUTO indicator appears on the display. • Press TUNING or . The receiver automatically searches for stations and stops when a station is found. FM Stereo AUTO TUNED Tip You can also press the TUNE MODE and arrow buttons on the remote control. - OR • To manually tune to a station: • Press TUNING MODE until the AUTO indicator goes off. • Press and hold TUNING or . The receiver tunes up or down the frequency band as long as you hold the button. Press the button repeatedly to tune up or down by steps. Tip • In Manual Tuning mode, FM stations are in mono. • If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. • You can also press the TUNE MODE and arrow buttons on the remote control. - OR • To tune to a station by entering the frequency: • Using the remote control, press TUNER repeatedly to select AM or FM, then press D.TUN. • Within eight seconds, press the number buttons to enter the frequency of the radio station you want. For example, to tune to 87.50, press 8, 7, then 5. Presetting FM or AM stations You can store a combination of as many as 40 of your favorite AM or FM stations as presets. To store a station as a preset: 1 Tune to the FM or AM station that you want to store as a preset. See "Listening to the radio" on page 17 for information on tuning your receiver. 2 Press MEMORY. The preset number flashes. 3 While the preset number is flashing (about eight seconds), press PRESET or to select a preset number from one through 40. 4 Press MEMORY again to store the station or channel. The station or channel is stored and the preset number stops flashing. www.insigniaproducts.com 17