Intel SR1680MV Service Guide - Page 53

Removing an HDD Backplane, Installing a 2.5-inch Pluggable SATA HDD Backplane, System Fans

Get Intel SR1680MV - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858210447
View all Intel SR1680MV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Note: Before you remove or install the power supply, complete the following steps: 1. Make sure the server is not turned on or connected to the AC power. To power off the server, see "Power Off". 2. Remove the motherboard cage module. To remove the cover, see "Removing the Server Board Cage Module". 3. Disconnect all necessary cable connections. Removing an HDD Backplane 1. Loosen the two securing screws on the backplane. 2. Lift the backplane up from motherboard. Figure 38. Remove the Screws and Lift the Backplane Up Installing a 2.5-inch Pluggable SATA HDD Backplane Reverse the "Removing an HDD Backplane" steps to install the 2.5-inch pluggable SATA HDD backplane. System Fans Each I/O board cage module includes three system fans. The six system fans on the server system share the same removal and installation procedures. For your reference, this section provides the steps for replacing one system fan on the right I/O board cage module as an example. The following figure shows the location of the system fan on the right I/O board cage module: Intel® Server System SR1680MV Service Guide 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
Intel
®
Server System SR1680MV Service Guide
33
Note:
Before you remove or install the power supply, complete the following steps:
1.
Make sure the server is not turned on or connected to the AC power. To power off
the server, see
“Power Off”
.
2.
Remove the motherboard cage module. To remove the cover, see
“Removing the
Server Board Cage Module”
.
3.
Disconnect all necessary cable connections.
Removing an HDD Backplane
1.
Loosen the two securing screws on the backplane.
2.
Lift the backplane up from motherboard.
Figure 38. Remove the Screws and Lift the Backplane Up
Installing a 2.5-inch Pluggable SATA HDD Backplane
Reverse the
“Removing an HDD Backplane”
steps to install the 2.5-inch pluggable SATA
HDD backplane.
System Fans
Each I/O board cage module includes three system fans. The six system fans on the server
system share the same removal and installation procedures. For your reference, this
section provides the steps for replacing one system fan on the right I/O board cage module
as an example.
The following figure shows the location of the system fan on the right I/O board cage
module: