JVC DT100U Instruction Manual - Page 81

Make connections, Load a cassette, Select input location on this VCR, Set recording speed

Get JVC DT100U - HMDT100 Digital VHS Recorder PDF manuals and user guides
UPC - 046838015267
View all JVC DT100U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

EN 81 A Make connections A Connection with the camcorder Connect a DV cable between the camcorder's DV connector and your VCR's [i.LINK] connector. B Connection with the VCR Connect an i.LINK cable between the playback VCR's i.LINK input/output connector and the recording VCR's [i.LINK IN/OUT] connector. B NOTES: • Depending on the devices equipped with the i.LINK connector which is connected to the VCR, picture noise on this VCR may differ from the noise on the connected devices. It is caused by the difference of the data processing method. • Connection with certain product(s) may not be supported. (A 'ATTENTION' on the back cover.) Load a cassette Insert the cassette to be recorded on into this VCR (for recording). C Select input location on this VCR On the front panel: Press [CHANNEL +/-] to select "I-1" etc. On the Remote: Press [TV/VCR CH +/-] to select "I-1" etc. D • When "I-1" is selected, either the front or the rear i.LINK connector can be used, the VCR will automatically switch to the appropriate connector being used. Set recording speed Press [REC SPEED] to set the recording speed. • For more details, refer to 'About Recording Speed' below. E Start playback Press [PLAY (I)] on the connected device. F NOTE: If the connected device is equipped with a superimpose/ OSD disable feature then set it to "OFF" before starting playback. Start recording On the front panel: Press [REC (R)]. On the Remote: Press [REC (R)] and [PLAY (I)] at the same time. NOTE: If "108 REC BY HS MODE" appears on the TV screen, refer to 'Error Codes and Messages' on page 92. Do not connect this VCR to the PC with the i.LINK cable. The operation is not guaranteed. About Recording Speed Input Source (Playback device) i.LINK/ DV input D-VHS DV-camcorder Digital Set Top Box (Others) Selectable Recording Speed (Recording device: This VCR) Auto (HS/STD)*, HS, STD, LS3 HS, STD, LS3 Auto (HS/STD)*, HS *Auto mode : The recording speed will be selected automatically according to the amount of data input (the transfer rate) from the i.LINK connector. NOTES: • When dubbing using the i.LINK connector, set the recording speed on the recording VCR to the same speed as the source tape on the playback VCR. • When Auto is selected for the recording speed, "AUT" and the selected speed appear on the front display panel in turn.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
EN
81
A
Make connections
A
Connection with the camcorder
Connect a DV cable between the camcorder’s
DV connector and your VCR’s [i.LINK]
connector.
B
Connection with the VCR
Connect an i.LINK cable between the
playback VCR’s i.LINK input/output connector
and the recording VCR’s [i.LINK IN/OUT]
connector.
NOTES:
•
Depending on the devices equipped with the i.LINK
connector which is connected to the VCR, picture
noise on this VCR may differ from the noise on the
connected devices. It is caused by the difference of
the data processing method.
•
Connection with certain product(s) may not be
supported. (
A
‘ATTENTION’ on the back cover.)
B
Load a cassette
Insert the cassette to be recorded on into this VCR
(for recording).
C
Select input location on this VCR
On the front panel:
Press [CHANNEL +/–] to select “I-1” etc.
On the Remote:
Press [TV/VCR CH +/–] to select “I-1” etc.
•
When “I-1” is selected, either the front or the
rear i.LINK connector can be used, the VCR will
automatically switch to the appropriate
connector being used.
D
Set recording speed
Press [REC SPEED] to set the recording speed.
•
For more details, refer to ‘About Recording
Speed’ below.
E
Start playback
Press [PLAY (
I
)] on the connected device.
NOTE:
If the connected device is equipped with a superimpose/
OSD disable feature then set it to “OFF” before starting
playback.
F
Start recording
On the front panel:
Press [REC (
R
)].
On the Remote:
Press [REC (
R
)] and [PLAY (
I
)] at the same time.
NOTE:
If “108 REC BY HS MODE” appears on the TV screen, refer to
‘Error Codes and Messages’ on page 92.
Do not connect this VCR to the PC with the i.LINK
cable. The operation is not guaranteed.
*Auto mode :
The recording speed will be selected automatically according to the amount of data input (the transfer
rate) from the i.LINK connector.
NOTES:
•
When dubbing using the i.LINK connector, set the recording speed on the recording VCR to the same speed as the source tape
on the playback VCR.
•
When Auto is selected for the recording speed, “AUT” and the selected speed appear on the front display panel in turn.
About Recording Speed
Input Source
(Playback device)
Selectable Recording Speed
(Recording device: This VCR)
i.LINK/ DV
input
D-VHS
Auto (HS/STD)*, HS, STD, LS3
DV-camcorder
HS, STD, LS3
Digital Set Top Box (Others)
Auto (HS/STD)*, HS