JVC GY-DV500E Instruction Manual - Page 35
VCR Setup Menu Cont'd - gy dv500 factory reset
View all JVC GY-DV500E manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 35 highlights
12-1 VCR Setup Menu (Cont'd) DISPLAYING AND SETTING VCR SETUP MENUS 12. SETUP MENU FILTER 1 3200k 2 5600k 3 5600k+ND SHUTTER STATUS MENU ALARM MONITOR AUTO IRIS FULL AUTO BLACK BACK L NORMAL SPOT L STRETCH NORMAL COMPRESS LOLUX PRST A B ON KNEE OFF AUTO BARS CAM HML SAVE STBY VTR GAIN OUTPUT WHT.BAL NG POWER ON OFF OPERATE/WARNING RESET MONITOR SELECT CH-1 AUDIO CH-2 LEVEL LIGHT ON OFF COUNTER CTL TC UB CH-1 AUDIO LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE MENU FRONT REAR GROUP HOLD ITEM SELECT DATA SET SHIFT ADVANCE PRESET 1. 6. 2. 4. 3. 5. "MENU" indication Viewfinder 000 100 200 300 400 500 HM : SERVO / SYSTEM : V I DEO : AUD I O : SYSTEM : T I ME CODE : ON SCREEN : HOUR METER GROUP menu screen for U-ver. Counter display 2 4 4 : LOW CUT 2 4 5 : SAMP L E RATE 2 4 6 : FRONT VOLUME OF F 48K ENAB L E Item menu screen DATA SET DATA SET display Viewfinder 000 200 300 500 HM : SERVO / SYSTEM : AUD I O : SYSTEM : ON SCREEN : HOUR METER GROUP menu screen for E-ver. 1. Engaging the VCR Setup Menu mode. Press the MENU button. • The "MENU" indication in the display section starts blinking and the VCR Setup Menu appears in the viewfinder and on the counter display. Note: When a cable is connected to the VTR REMOTE connector, the VTR Setup Menu is not displayed in the viewfinder. 2. Selecting the GROUP. Press the GROUP button. • Each time the GROUP button is pressed the selected GROUP number is shown blinking on the viewfinder screen. The counter display shows the selected group. 3. Open the Item menu of the selected GROUP. Press the SELECT button. 4. Selecting the Item. Press the ITEM button. • Each time the ITEM button is pressed the selected item number is shown blinking on the viewfinder screen. The counter display shows the selected item. 5. Changing the setting value of the item. Press the SELECT button and select the setting value. When multiple items should be set, repeat the operations of steps 4. and 5. To set menu items in other groups, press the MENU button. When the relevant group menu is displayed, perform the setting. When the GROUP button is pressed, the items of the higher order group menu are displayed. 6. Saving the setting value. Press the DATA SET button. • "DATA SET" appears in the viewfinder and on the counter display and the setting value is saved in the GY-DV500's memory. The display returns to the normal screen mode when data has been saved. If the MENU button is pressed without pressing the DATA SET button, the display returns to the normal screen mode without the setting value being changed. 67 12. SETUP MENU 12-1 VCR Setup Menu (Cont'd) VCR SETUP MENU CONTENTS Group SERVO /SYSTEM VIDEO (U-ver. only) AUDIO Item Setting Value Upper row: Viewfinder display Lower row: Counter display indication 050: REMOTE SELECT LOCAL IEEE1394 RS232C rnSL Lc IE 23 Contents Factory Setting Selection of the method for remote control of the VCR. LOCAL : Choose this setting when the VCR should be controlled using the operation buttons on the GY-DV500 only. IEEE1394 : Choose this setting when the VCR should be remote controlled from a DV connector equipped video component connected to the DV connector on the rear section of the GY-DV500. RS232C : Choose this setting for control by means of the VCR remote control signal from the VTR REMOTE connector on the GY-DV500. * The operation buttons on the GY-DV500 remain effective even when set to IEEE1394 or RS232C. LOCAL 082: BACK TALLY MODE rtMd OFF ON BLINK oF on bL Selection of the lighting pattern of the BACK TALLY lamp on the rear section during recording. OFF : The lamp is always off. ON : The lamp lights during recording. It remains off until the VTR trigger button is pressed to start the recording. BLINK : The lamp lights during recording. It blinks when the VTR trigger button is pressed to start the recording. BLINK 126: INPUT SELECT vld CAMERA IEEE1394 cA IEEE1394 Selection of the input video signal. Settings cannot be changed during recording. CAMERA : Camera image is input. IEEE1394 : The image from the DV connector equipped video component connected to the DV connector on the rear section is input. CAMERA 244: LOW CUT LctF OFF CH1 CH2 CH1 & CH2 oF 01 02 on To select whether or not the low frequencies of the audio signal from the audio input connectors are cut. Set to ON to reduce the wind noise of the microphone. OFF : The CH1 and CH2 low frequencies are not cut. CH1 : Only the low frequencies of the audio signal input to the CH1 channel are cut. CH2 : Only the low frequencies of the audio signal input to the CH2 channel are cut. CH1& CH2 :The low frequencies are cut for both CH1 and CH2. OFF 245: SAMPLING RATE snPL 32K To select the sampling rate for digital PCM audio recording. 48K 48K 32K : Digital recording occurs with 12-bit, 32 kHz sampling 32 48K : Digital recording occurs with 16-bit 48 kHz 48 sampling. * The DV format offers recording tracks for up to 4 channel when recording using 12-bit, 32 kHz sampling. The GY-DV500 records two of these tracks. The GY-DV500 does not allow after-recording. 246: FRONT VOLUME ENABLE FruL DISABLE ENABLE oF on To select whether or not the front section recording level control should be operative. The front section recording level control only affects the audio signal recorded on CH1. DISABLE : Use of the front section recording level control is disabled. ENABLE : Use of the front section recording level control is enabled. * The CH-1 recording level control on the side section works regardless of the setting. ENABLE 68