Kenwood DNX7140 Owner's Manual (pdf) - Page 93

Help? - problem

Get Kenwood DNX7140 - Navigation System With DVD player PDF manuals and user guides
UPC - 019048182494
View all Kenwood DNX7140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Help? Troubleshooting Some functions of this unit may be disabled by some settings made on this unit. ! • Cannot set up the subwoofer. • Cannot set up subwoofer phase. • No output from the subwoofer. • Cannot set up the low pass filter. • Cannot set up the high pass filter. ▲ Subwoofer is not set to On. ☞ (page 76) ▲ The DSP Select is Bypass. ☞ (page 76) ▲ The Dual zone function is enabled. ☞ (page 61) ▲ The unit is set to STANDBY source. ! • Cannot select the output destination of the subsource in the Dual zone. • Cannot adjust the volume of the rear speakers. ▲ The Dual zone function is disabled. ☞ (page 61) ! Cannot play audio files. ▲ "CD Read" of (page 80) is set to "2". ! Cannot Folder select. ▲ The Random play function is enabled. ! Cannot perform Repeat play. ▲ The PBC function is enabled. ! • Cannot set up the equalizer. • Cannot set up the crossover network. ▲ The Dual zone function is enabled. ☞ (page 61) ▲ The DSP Select is Bypass. ☞ (page 76) ▲ The equalizer is set to "iPod". ☞ (page 60) ▲ The unit is set to STANDBY source. What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The Touch Sensor Tone doesn't sound. ✔ The preout jack is being used. ☞ The Touch Sensor Tone can't be output from the preout jack. Tuner source ? Radio reception is poor. ✔ The car antenna is not extended. ☞ Pull the antenna out all the way. ✔ The antenna control wire is not connected. ☞ Connect the wire correctly, referring to the section on . Disc source ? The specified disc does not play, but another one plays instead. ✔ The specified CD is quite dirty. ☞ Clean the CD. ✔ The disc is severely scratched. ☞ Try another disc instead. Audio file source ? The sound skips when an Audio file is being played. ✔ The media is scratched or dirty. ☞ Clean the media, referring to the CD cleaning of the section on (page 6). ✔ The recording condition is bad. ☞ Record the media again or use another media. English 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
English
93
Help?
Troubleshooting
Some functions of this unit may be disabled by
some settings made on this unit.
!
•
Cannot set up the subwoofer.
•
Cannot set up subwoofer phase.
•
No output from the subwoofer.
•
Cannot set up the low pass filter.
•
Cannot set up the high pass filter.
▲
Subwoofer is not set to On.
☞
<Speaker Setup>
(page 76)
▲
The DSP Select is Bypass.
☞
<DSP Bypass
Control> (page 76)
▲
The Dual zone function is enabled.
☞
<Zone
Control> (page 61)
▲
The unit is set to STANDBY source.
!
•
Cannot select the output destination of the
subsource in the Dual zone.
•
Cannot adjust the volume of the rear
speakers.
▲
The Dual zone function is disabled.
☞
<Zone
Control> (page 61)
!
Cannot play audio files.
▲
"CD Read" of <Disc Setup> (page 80) is set to
"2".
!
Cannot Folder select.
▲
The Random play function is enabled.
!
Cannot perform Repeat play.
▲
The PBC function is enabled.
!
•
Cannot set up the equalizer.
•
Cannot set up the crossover network.
▲
The Dual zone function is enabled.
☞
<Zone
Control> (page 61)
▲
The DSP Select is Bypass.
☞
<DSP Bypass
Control> (page 76)
▲
The equalizer is set to "iPod".
☞
<Equalizer
Control> (page 60)
▲
The unit is set to STANDBY source.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
General
?
The Touch Sensor Tone doesn’t sound.
✔
The preout jack is being used.
☞
The Touch Sensor Tone can’t be output from
the preout jack.
Tuner source
?
Radio reception is poor.
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
✔
The antenna control wire is not connected.
☞
Connect the wire correctly, referring to the
section on <INSTALLATION MANUAL>.
Disc source
?
The specified disc does not play, but another
one plays instead.
✔
The specified CD is quite dirty.
☞
Clean the CD.
✔
The disc is severely scratched.
☞
Try another disc instead.
Audio file source
?
The sound skips when an Audio file is being
played.
✔
The media is scratched or dirty.
☞
Clean the media, referring to the CD
cleaning of the section on <Handling discs>
(page 6).
✔
The recording condition is bad.
☞
Record the media again or use another
media.