Kenwood DVR-7000 User Manual - Page 63

63 DVR-505/DVR-7000 (EN) Remote control unit Symptom Remote control operation is not possible. Cause ÷ Batteries are exhausted. ÷ The remote control is too far away from the system, the controlling angle is deviated or there is an obstacle in between. ÷ There is no disc set in the component to be played. Remedy ÷ Replace with new batteries. & ÷ Operate the unit inside the remote control- lable range. & ÷ Set a disc in the component to be played. ∞ ÷ Operation has been performed with the keys of the main unit. ÷ A nonfunctional key has been pressed ÷ Perform operation after once pressing the key for the input or device to be operated. * DVD / CD player unit Symptom Cause Remedy Playback does not start when the play (6) key is pressed. ÷ There is no disc in the player. ÷ There are no signals recorded on the side of the disc being played. ÷ Load a disc and press the play (6) key. ∞ ÷ Turn the disc over and properly place it on ∞ the disc tray. Playback starts but no image/sound is seen/heard. ÷ The TV is not turned on. ÷ The connection cords are not properly con- nected. ÷ Turn on the TV. ÷ Properly reconnect the connection cords. $ The picture is disrupted when the im- ÷ The picture is slightly disrupted during fast ÷ This is not a malfunction. age is fast forwarded or fast reversed. forward and fast reverse operations. No sound is heard. ÷ The volume control of this set is not adjusted properly. ÷ The player is in a special playback mode. ÷ Set the sound volume to an appropriate * level. ÷ Press the play (6) key to resume normal ∞ playback mode. The picture does not look good or the picture/sound quality is poor. ÷ A nearby device is generating noise. ÷ The disc is dirty. ÷ The disc is damaged. ÷ There is condensation on the optical lens. ÷ Separate this unit as far as possible from the device you think is generating the noise. ÷ Refer to the "Disc handling precautions" 8 section and wipe dirt from the disc. ÷ Use a new disc. ÷ Refer to the "Caution on condensation" section and evaporate the condensation. 7 It takes a while for the disc to start playing. ÷ Time is required for the unit to detect the disc type and size and for the rotation of the motor to stabilize. This is not a malfunction. ÷ Approximately 10 to 20 seconds are required for a disc to start playing, although the time differs depending on the disc. The top and bottom of the screen cannot be seen. ÷ The video format of the disc being played does not match that of the connected TV monitor. ÷ Refer to the "Examples of TV screen dis- 0 play of each video format" section ,and use a disc with the appropriate video format for your TV or a TV with the appropriate video format for the disc. A VCD cannot be played using menus. ÷ The VCD disc being played is not compat- ÷ Menu playback is available only with VCD ‡ ible with P.B.C. discs recorded with P.B.C. The subtitle is not displayed. ÷ The DVD disc being played does not contain the recording of subtitles. ÷ The subtitle mode is set to off. ÷ The subtitle cannot be displayed when the DVD disc being played does not contain the recording of subtitles. ÷ Press the S.TITLE key to switch on the ª subtitle mode. The voice (or subtitle) language cannot be changed. ÷ The DVD disc being played does not contain the recording of more than one audio (or subtitle) language. ÷ The voice (or subtitle) language cannot be changed when the DVD disc being played does not contain the recording of more than one voice (or subtitle) language. Knowledge