Kenwood TS-2000 Operation Manual - Page 18

GETTING ACQUAINTED FRONT PANEL 3 4 5 6 7 8 9 10 12 PF F LOCK A ATT LEVEL VOX PRE LEVEL PROC SEND ANT1/2 AT PHONES LEVEL LEVEL MIC MANUAL N.R. LO/ WIDTH B.C. A.N. 1 2 3 CH1/REC CH2/REC CH3/REC 4 5 6 TONE/SEL METER CTCSS/SEL 7 8 9 NB/LEVEL AGC/OFF FINE/STEP . 0 DCS/SEL SHIFT/OFFSET ENT HI/ SHIFT FUNC MAIN CAR MIC TX MONI PWR DELAY KEY AUTO LSB USB REV CW FSK NAR FM AM CLR DISP SEL 1MHz HF/VHF/UHF ALL MODE MULTI BANDER TS-2000 CW TUNE RIT ALT XIT 9.6k STA CON RIT/SUB SUB MENU TFSET _ CLEAR P.C.T SET QUICK MEMO MANUAL BC MAIN RF GAIN MR M.IN + MULTI CH C.IN CALL MAIN SUB CTRL SG.SEL SCAN SATL M/S REV A/B SPLIT VFO/CH TRACE VFO/M A=B MG.SEL M VFO M.IN MAIN AF SUB SQL 11 13 12 q PF key You can assign a function to this Programmable Function key. The default function is Voice 1 {page 77}. w [ ] (POWER) switch Press and hold briefly to switch the transceiver power ON. Press again to switch the power OFF. e ATT/ F LOCK key Press to switch the receiver attenuator ON or OFF {page 57}. Press [FUNC], [ATT/ F LOCK] to switch the Frequency Lock function ON or OFF {page 77}. r PRE/ LOCK A key Press to switch the receiver pre-amplifier ON or OFF {page 57}. Press [FUNC], [PRE/ LOCK A] to lock all the transceiver keys {page 77}. t VOX/ LEVEL key In voice mode, press to switch the Voice-Operated Transmit function ON or OFF {page 39}. In CW mode, press to switch the Break-in function ON or OFF {page 42}. Press [FUNC], [VOX/ LEVEL] to adjust the microphone input level for VOX operation. The VOX LED lights orange when the VOX function is active. y PROC/ LEVEL key Press to switch the Speech Processor for transmitting ON or OFF {page 40}. Press [FUNC], [PROC/ LEVEL] to adjust the Speech Processor input level. The PROC LED lights orange when the Speech Processor function is actived. u SEND key Press to switch the transceiver between receive mode and transmit mode {pages 5, 7}. i AT/ ANT1/2 key Press to activate the internal antenna tuner {page 72} or an external antenna tuner. Press [FUNC], [AT/ ANT1/2] to select either Antenna 1 or Antenna 2 for the HF/ 50 MHz band {page 72}. o PHONES jack Connect a set of headphones to this jack. Inserting a plug into the jack automatically mutes the audio from the speaker {pages 3, 78}. !0 MIC connector Connect a compatible microphone to this connector, then securely screw down the connector locking ring {page 3}. !1 N.R./ LEVEL key Press to switch the DSP Noise Reduction function ON or OFF. Press [FUNC], [N.R./ LEVEL] to adjust the Noise Reduction level. Press [FUNC], [N.R./ LEVEL] again to finish the adjustment {page 56}. !2 A.N./ LEVEL key Press to switch the DSP Auto Notch function ON or OFF. Press [FUNC], [A.N./ LEVEL] to adjust the DSP Auto Notch reduction level. Press [FUNC], [A.N./ LEVEL] again to finish the adjustment {page 56}. !3 B.C./ MANUAL key Press to switch the DSP Auto Beat Cancel function ON or OFF. Press [FUNC], [B.C./ MANUAL] to adjust the beat cancel frequency manually. Press [FUNC], [B.C./ MANUAL] again to finish the manual adjustment {page 56}. 8