Kenwood TS-2000 Operation Manual - Page 61
Radio Teletypewriting Rtty, Cw/ Fsk/ Rev], Func], Send], Pwr/ Tx Moni]
![]() |
View all Kenwood TS-2000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 61 highlights
RADIO TELETYPEWRITING (RTTY) RTTY is the data communications mode with the longest history. It was originally designed for use with mechanical teletypewriters which were often used before personal computers became common. Now you can easily start operating RTTY with a personal computer and MCP. Unlike Packet, each time you type a letter, it is transmitted over the air. What you typed is transmitted and displayed on the computer screen of the recipient. RTTY operation uses frequency shift keying (FSK) and the 5-bit Baudot code or the 7-bit ASCII code to transmit information. For the cable connections, see "RTTY" {page 95}. For further information, consult reference books about Amateur Radio. 1 Access Menu No. 38 and select an FSK shift. • FSK shift is the difference in frequencies between a mark and a space. • The 170 Hz default is used on the Amateur bands. 2 Access Menu No. 39 and select a key-down polarity. • Select "NORMAL" to transmit a mark when keying down or "INVERS" to transmit a space. The default is "NORMAL". 3 Access Menu No. 40 and select high tone (2125 Hz) or low tone (1275 Hz) for mark. • High tone (default) is commonly used nowadays. 4 Select an operating frequency. 5 Press [CW/ FSK/ REV] to select FSK. • "FSK" appears. 6 If necessary to be compatible with the other station, press [FUNC], [CW/ FSK/ REV] to reverse the transceiver to the upper sideband. • "FSR" appears. 11 SPECIALIZED COMMUNICATIONS 7 Following the instructions provided with your MCP, enter a command from your computer to select transmit mode. • The MAIN band LED changes from green (RX) to red (TX). • You may instead press [SEND] to manually select the transmit mode. 8 Begin sending data from your computer. • Use Menu No. 50C to select the appropriate AF output level. The AF control cannot be used for this adjustment. • Press [FUNC], [PWR/ TX MONI] to monitor your signals. Press [FUNC], [PWR/ TX MONI] again to quit this function. 9 When finished transmitting, enter a command from your computer to return to receive mode. • The MAIN band LED changes from red (TX) to green (RX). • If you pressed [SEND] in step 7, press [SEND] again. The frequencies (measured in kHz) commonly used for RTTY operation are listed below: U.S.A./ Canada 1800 ~ 1840 3605 ~ 3645 (DX: 3590) 7080 ~ 7100 (DX: 7040) 10140 ~ 10150 14070 ~ 14099.5 18100 ~ 18110 21070 ~ 21100 24920 ~ 24930 28070 ~ 28150 IARU Region 1 (Europe/ Africa) 1838 ~ 1842 3580 ~ 3620 7035 ~ 7045 10140 ~ 10150 14080 ~ 14099.5 18101 ~ 18109 21080 ~ 21120 22920 ~ 24929 28050 ~ 28150 Note: You may adjust the carrier level when necessary. Press [FUNC], [MIC/ CAR] to enter the adjustment mode. With a key down condition, turn the MULTI/ CH control so that the ALC meter reads in the ALC zone but does not exceed the upper ALC zone limit. • Traditionally, the lower sideband is used for FSK operation. • Press [FUNC], [CW/ FSK/ REV] to return to the lower sideband. 51
![](/manual_guide/products/kenwood-ts2000-operation-manual-ab192f5/61.png)