Kenwood TS-2000 Operation Manual - Page 74
Quick Memory, Memory Features, Memory Group, Storing Into Quick Memory
View all Kenwood TS-2000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 74 highlights
13 MEMORY FEATURES MEMORY GROUP To manage 300 memory channels, you can divide them up into a maximum of 10 groups (Groups 0 to 9). After you configure a Memory Group, you can select one or more of the Memory Groups you want to recall, in Memory Recall mode. As a default, all memory channels are stored in Group 0. To change the Memory Channel Group: 1 Press [M.IN] to enter Memory Scroll mode. 2 Select the desired memory channel for which you want to change the Memory Group by turning the MULTI/ CH control. 3 Press [DISP]. • The Memory Name input prompt appears. 4 Press [DISP] again to skip the input or enter a Memory Name using [+]/ [-] and [MAIN] or [SUB] {page 63}. • The current Memory Group appears in a larger font. 5 Press a numeric key to change the selected Group number. The newly selected Group number appears in a larger font. 6 Press [M.IN] to store the settings. ■ Memory Group Select After you configure Memory Groups to the Memory Channels, you can select one or more of the Groups to be recalled in Memory Recall mode. To select Memory Groups: 1 Press [FUNC], [MsVFO/ MG.SEL] to enter Memory Group Select mode. 2 Numbers 0 ~ 9 appear in the main dot-matrix display. The selected Memory Group numbers are displayed in larger fonts. To change the selection, press a numeric key. To select all the Memory Groups, press [•/ DCS/SEL]. At least, one Memory Group must be selected. 3 Press [M.IN] to save the setting and exit. 4 You can now recall only the selected Memory Groups in Memory Recall mode. 64 QUICK MEMORY Quick memory is designed to quickly and temporarily save data without specifying a particular memory channel. Use Quick memory to store data you will not use in future operating sessions. For example, as you tune across the band looking for DX, it is convenient to store stations that you want to contact. You can quickly jump between several different memory channels as you monitor them. This transceiver provides ten Quick memory channels ("0_" to "9_") that can store the following data: VFO A frequency and operating mode Sub-receiver ON/ OFF RIT ON/ OFF VFO B frequency and operating mode Sub-receiver frequency and operating mode XIT ON/ OFF RIT/ XIT offset frequency Receiver filter bandwidth Noise Blanker ON/ OFF DSP Noise Reduction OFF/ 1/ 2 DSP Auto Notch ON/ OFF FINE ON/ OFF DSP Beat Cancel ON/ OFF TX/ RX functions STORING INTO QUICK MEMORY Each time you store a new frequency, all previously stored frequencies are bumped to the next respective Quick memory channel. When all ten memory channels contain frequencies, storing one more frequency bumps the contents of memory channel 9 off the stack (the data is lost). The following diagram illustrates how the Quick Memory stacks the data in memory each time you press QUICK MEMO [M.IN]. New data 24.911 Memory 0 144.005 Memory 1 14.235 Memory 2 441.250 Memory 3 18.111 Memory 4 50.015 7.082 29.610 3.545 145.250 Memory 5 Memory 6 Memory 7 Memory 8 Memory 9 New data 21.005 Memory 0 24.911 Memory 1 144.005 Memory 2 14.235 Memory 3 441.250 Memory 4 18.111 50.015 7.082 29.610 3.545 Memory 5 Memory 6 Memory 7 Memory 8 Memory 9 New data 14.085 Memory 0 21.005 Memory 1 24.911 Memory 2 144.005 Memory 3 14.235 Memory 4 441.250 18.111 50.015 7.082 29.610 Memory 5 Memory 6 Memory 7 Memory 8 Memory 9 Note: To use the Quick memory channels, you must operate both the main transceiver and the sub-receiver in VFO mode. If you are using the Quick memory channels while the sub-receiver is turned off, its last operating mode must be VFO mode. Turning the sub-receiver off while it is recalling a memory channel will not allow you to use the Quick memory function.