Kenwood TS-2000 Operation Manual - Page 28
Operating Basics, Switching Power On/off, Adjusting Volume, Selecting Vfo A Or Vfo B
View all Kenwood TS-2000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 28 highlights
OPERATING BASICS SWITCHING POWER ON/OFF 1 Switch the DC power supply ON. 2 Press and hold [ ] (POWER) briefly to switch the transceiver ON. • Do not press the switch for more than approximately 2 seconds; the transceiver will be switched OFF. • Upon power up, "HELLO" appears, followed by the selected frequency and other indicators. PF F LOCK A ATT LEVEL VOX PRE LEVEL PROC SEND ANT1/2 AT PF F LOCK A ATT LEVEL VOX PRE LEVEL PROC SEND ANT1/2 AT PHONES LEVEL LEVEL MIC MANUAL N.R. LO/ WIDTH B.C. A.N. 1 2 3 CH1/REC CH2/REC CH3/REC 4 5 6 TONE/SEL METER CTCSS/SEL 7 8 9 NB/LEVEL AGC/OFF FINE/STEP . 0 DCS/SEL SHIFT/OFFSET ENT HI/ SHIFT FUNC MAIN CAR MIC TX MONI PWR DELAY KEY AUTO LSB USB REV CW FSK NAR FM AM CLR DISP SEL 1MHz HF/VHE/UHF ALL MO MEN CTRL RADIO FREQUENCY (RF) GAIN Set the MAIN RF GAIN control fully clockwise. You may turn it counterclockwise slightly when you have trouble hearing the desired signal because of excessive atmospheric noise or interference from other stations. First take note of the peak S-meter reading of the desired signal. Then turn the MAIN RF GAIN control counterclockwise until the S-meter reads the peak value that you noted. Signals that are weaker than this level will be attenuated and reception of the station will become easier. MANUAL BC MAIN RF GAIN UTO B SB SEL 1MHz HF/VHE/UHF ALL MODE MULTI BANDER TS-2000 CW TUNE RIT ALT XIT 9.6k STA CON RIT/SUB SUB MENU TFSET _ CLEAR P.C.T SET QUICK MEMO MANUAL BC MAIN RF GAIN MR M.IN + MULTI CH C.IN CALL MAIN SUB CTRL SG.SEL SCAN SATL M/S REV A/B SPLIT VFO/CH TRACE VFO/M A=B MG.SEL M VFO M.IN MAIN AF SUB SQL 3 To switch the transceiver OFF, press [ ] (POWER) again. 4 Switch the DC power supply OFF. • You may skip step 3. After switching the transceiver ON, you can switch it OFF or ON using only the power switch of the DC power supply. The transceiver stores the information of the POWER switch position when the DC power source is switched OFF. ADJUSTING VOLUME AUDIO FREQUENCY (AF) GAIN Turn the MAIN AF control clockwise to increase the audio level and counterclockwise to decrease the level. MAIN AF SQL UTO B SB SEL 1MHz HF/VHE/UHF ALL MODE MULTI BANDER TS-2000 CW TUNE RIT ALT XIT 9.6k STA CON RIT/SUB SUB MENU TFSET _ CLEAR P.C.T SET QUICK MEMO MANUAL BC MAIN RF GAIN MR M.IN + MULTI CH C.IN CALL MAIN SUB CTRL SG.SEL SCAN SATL M/S REV A/B SPLIT VFO/CH TRACE VFO/M A=B MG.SEL M VFO M.IN MAIN AF SUB SQL Note: ◆ The position of the MAIN AF control does not affect the volume of beeps caused by pressing keys nor the CW transmit sidetone. The audio level for Packet operation is also independent of the MAIN AF control setting. ◆ When the optional RC-2000 is installed, you can control the volume with the AF controls on both the transceiver and the RC-2000. However, when turning the transceiver on, the volume settings of the RC-2000 have priority. Depending on the type and gain of your antenna, and the condition of the band, you may also prefer leaving the MAIN RF GAIN control turned counterclockwise by the same amount rather than turning it fully clockwise. When using FM mode, always set the MAIN RF GAIN control fully clockwise. SELECTING VFO A OR VFO B 2 VFOs are available for controlling the frequency on the main transceiver. Each VFO, VFO A and VFO B, works independently so that a different frequency and mode can be selected. When SPLIT operation is activated, VFO A is used for reception and VFO B is used for transmission. The opposite combination is also possible. Press [A/B] to toggle between VFO A and VFO B. • "tA" or "tB" appears to indicate which VFO is selected. SATL M/S REV A/B SPLIT VFO/CH TRACE VFO/M A=B UTO B SB SEL 1MHz HF/VHE/UHF ALL MODE MULTI BANDER TS-2000 CW TUNE RIT ALT XIT 9.6k STA CON RIT/SUB SUB MENU TFSET _ CLEAR P.C.T SET QUICK MEMO MANUAL BC MAIN RF GAIN MR M.IN + MULTI CH C.IN CALL MAIN SUB CTRL SG.SEL SCAN SATL M/S REV A/B SPLIT VFO/CH TRACE VFO/M A=B MG.SEL M VFO M.IN MAIN AF SUB SQL SELECTING A BAND Press [+]/ [-] to select your desired band. • Holding down either key changes the bands continuously. MAIN SUB UTO B SB SEL 1MHz HF/VHE/UHF ALL MODE MULTI BANDER TS-2000 CW TUNE RIT ALT XIT 9.6k STA CON RIT/SUB SUB MENU TFSET CLEAR _ P.C.T SET QUICK MEMO MANUAL BC MAIN RF GAIN MR M.IN + MULTI CH C.IN CALL MAIN SUB CTRL SG.SEL SCAN SATL M/S REV A/B SPLIT VFO/CH TRACE VFO/M A=B MG.SEL M VFO M.IN MAIN AF SUB SQL 18