Kenwood TS-590S User Manual - Page 15

Lcd Display

Get Kenwood TS-590S PDF manuals and user guides View all Kenwood TS-590S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

LCD DISPLAY A B C 2 GETTING ACQUAINTED D E F -- A -- While receiving, the meter serves as an S-meter to measure and display the received signal strength. While transmitting, it serves as a power meter plus an ALC meter, an SWR meter, or a Speech Processor compression meter. The Peak Hold function holds each reading for approximately half a second. While adjusting the IF filter bandwidth, the meter displays an adjustment state. -- B -- Appears when the Auto Mode function is ON and while in Auto Mode frequency setup {page 51}. Displays the operating mode (USB, LSB, FM, AM, CW, CWR, FSK, or FSR) {page 11}. Appears while in Menu mode {page 14}. Appears while in Memory Scroll mode {page 42}. Appears while in Memory Channel mode or Memory Scroll mode {page 42}. In normal operating mode and various configuration modes, it displays the Memory Channel number, Quick Memory number, and entry log number. In Menu mode, it displays the Menu No. -- C -- Appears while in Data mode {page 38}. Appears while in narrow FM mode {page 11}. Appears when the receiver pre-amplifier is ON {page 40}. Appears when the receiver's attenuator is ON {page 40}. Appears when the Noise Blanker 1 or 2 is ON {page 40}. " " (fast) or " " (slow) appears when the Automatic Gain Control function is ON. " " appears when the AGC is OFF {page 29}. Appears when IF filter A is selected {page 38}. Appears when IF filter B is selected {page 38}. -- D -- " " appears when manual notch is set to Normal. " " appears when Manual Notch is set to Wide. " " appears when Auto Notch is selected {page 39}. Appears when the Fine Tuning function is ON {page 29}. Appears when the MHz Step function is ON {page 28}. Also appears when the Quick Menu function is ON {page 14}. " " or " " appears, depending on whether DSP Noise Reduction 1 or Noise Reduction 2 is selected {page 39}. " " appears when the RX Equalizer function is ON {page 55}. " " appears when the TX Equalizer function is ON {page 32}. " " or " " appears, when you select the DSP Beat Cancel 1 or Beat Cancel 2 {page 39}. " " appears when the Tone function is ON {page 25}, and blinks during Tone scan. " " appears when the CTCSS (Continuous Tone Coded Squelch System) function is ON, and blinks during CTCSS scan {page 26}. " " appears when the Cross Tone function is ON {page 27}. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
7
2
GETTING ACQUAINTED
——
A
——
While receiving, the meter serves as an S-meter to
measure and display the received signal strength.
While transmitting, it serves as a power meter plus an
ALC meter, an SWR meter, or a Speech Processor
compression meter.
The Peak Hold function holds
each reading for approximately half a second.
While
adjusting the IF filter bandwidth, the meter displays an
adjustment state.
——
B
——
Appears when the Auto Mode function is ON and
while in Auto Mode frequency setup {page 51}.
Displays the operating mode (USB, LSB, FM, AM,
CW, CWR, FSK, or FSR) {page 11}.
Appears while in Menu mode {page 14}.
Appears while in Memory Scroll mode {page 42}.
Appears while in Memory Channel mode or Memory
Scroll mode {page 42}.
In normal operating mode and various configuration
modes, it displays the Memory Channel number,
Quick Memory number, and entry log number.
In
Menu mode, it displays the Menu No.
——
C
——
Appears while in Data mode {page 38}.
Appears while in narrow FM mode {page 11}.
Appears when the receiver pre-amplifier is ON {page
40}.
Appears when the receiver’s attenuator is ON {page
40}.
Appears when the Noise Blanker 1 or 2 is ON
{page 40}.
“
” (fast) or “
” (slow) appears when the
Automatic Gain Control function is ON.
“
”
appears when the AGC is OFF {page 29}.
Appears when IF filter A is selected {page 38}.
Appears when IF filter B is selected {page 38}.
——
D
——
“
” appears when manual notch is set to Normal.
“
” appears when Manual Notch is set to Wide.
“
” appears when Auto Notch is selected {page
39}.
Appears when the Fine Tuning function is ON {page
29}.
Appears when the MHz Step function is ON {page
28}.
Also appears when the Quick Menu function is
ON {page 14}.
“
” or “
” appears, depending on whether
DSP Noise Reduction 1 or Noise Reduction 2 is
selected {page 39}.
“
” appears when the RX Equalizer function is ON
{page 55}.
“
” appears when the TX Equalizer
function is ON {page 32}.
“
” or “
” appears, when you select the DSP
Beat Cancel 1 or Beat Cancel 2 {page 39}.
“
” appears when the Tone function is ON {page 25},
and blinks during Tone scan.
“
” appears when the
CTCSS (Continuous Tone Coded Squelch System)
function is ON, and blinks during CTCSS scan {page
26}.
“
” appears when the Cross Tone function is
ON {page 27}.
LCD DISPLAY
A
B
C
D
E
F